moddedcorsa
Member
Registered: 15th Aug 02
Location: Argyll, West scotland
User status: Offline
|
Hi, just got a w-reg 1.2 16v sxi. The car has no engine, but ive a x16xe i intend to rebuild and fit.
Just wondering if any1 can identify what the following plugs are?
Starter and altenator ive labled,
Speedo drive appears to be top (with orange water seal)
And the big plug with the clamp (and orange water seal is the ecu)
Also when i run the x16 loom into the car down in the drivers footwell, will the feeds for it be there, or am i going to have to remove the dash and trace where they come from?
Only other question i have at the moment is the whether the sxi fuel pump will be up to the job, anybody know?
Cheers, Gary
[Edited on 28-02-2012 by moddedcorsa]
|
one-mr-t
Member
Registered: 4th Aug 09
Location: Greater Manchester
User status: Offline
|
Fuel pump will be fine, you can either change the dash loom to a sport one or butcher the one that's already there
|
moddedcorsa
Member
Registered: 15th Aug 02
Location: Argyll, West scotland
User status: Offline
|
Whats the most common method? As there must be loads of converted sxi's
|
Dan H
Member
Registered: 27th Nov 08
Location: Stockton-on-Tees
User status: Offline
|
get a new dash loom from an 1.2/1.4 8v or 1.4/1.6 16v and change it oer, should be plug and play after that
|
moddedcorsa
Member
Registered: 15th Aug 02
Location: Argyll, West scotland
User status: Offline
|
hmm, then the epas wont work, as the fuse box with it is smaller to account for the motor sticking out the coloumn. Really want to keep this..
|
one-mr-t
Member
Registered: 4th Aug 09
Location: Greater Manchester
User status: Offline
|
Change it all to the hydrolic power steering much better
|
moddedcorsa
Member
Registered: 15th Aug 02
Location: Argyll, West scotland
User status: Offline
|
lol, this isnt answering my original question, or any help on the wiring. Ill probably just grab a haynes manual and spend time figuring it out myself, as nobody seems to know (which i find hard to believe, as this engine has probably been removed for conversions for over 10 years now)
|
.Matt
Member
Registered: 28th Jan 09
Location: Kent
User status: Offline
|
This is a post of a 1.2 to 2.0,
I guess you will need to find 1.6 to 2.0 which wont be hard and just get the colours and match
http://www.corsasport.co.uk/board/viewthread.php?tid=611430&highlight=1&pid=8039226#pid8039226
|
moddedcorsa
Member
Registered: 15th Aug 02
Location: Argyll, West scotland
User status: Offline
|
Thanks matt, just had a read of that. Seems the wiring is just as easy as any other corsa conversion only a bit more time consuming 
[Edited on 28-02-2012 by moddedcorsa]
|
moddedcorsa
Member
Registered: 15th Aug 02
Location: Argyll, West scotland
User status: Offline
|
Can anyone clarify what the above un-labled plugs are?
Also do the 2 grey ones plug together?
|
jamieSxi
Member
Registered: 20th Sep 11
Location: Northern ireland (Lurgan)
User status: Offline
|
Is this a 1.2 sxi loom??
|
Linch
Member
Registered: 4th May 06
Location: Whickham, Tyne and Wear
User status: Offline
|
One At the bottom is reverse light sensor, grey plugs are ingnition plugs if they come from separate places.
|
moddedcorsa
Member
Registered: 15th Aug 02
Location: Argyll, West scotland
User status: Offline
|
yeah it is jamie (bought the car without its engine, so not 100% on what goes where)
|
