Mo
Member
Registered: 29th Jan 03
Location: Bolton, Drives Q3 S-line +
User status: Offline
|
back seat won't fold forward when i press the button on top of the seat. its a corsa b. Can this be fixed?
|
willay
Moderator
Organiser: South East, National Events
Premium Member
Registered: 10th Nov 02
Location: Roydon, Essex
User status: Offline
|
given it a bash? made sure buttons on both sides have been pressed down when you push it?
Check the hinges on the side to see if anythign is jammed in there, might jsut need some wd40 and a slap.
|
Fro
Member
Registered: 20th Jun 06
Location: Rainham, Essex Drives: A3 2.0TDi Sport
User status: Offline
|
I get this because i wedged my sub against it, if you kneel on the back seat press the button down with one hand and then hit it hard towards the boot it should pop free and you can pull it forward.
|
Mo
Member
Registered: 29th Jan 03
Location: Bolton, Drives Q3 S-line +
User status: Offline
|
will try it but i'm sure it's well and truely jammed
|
gavin18787
Premium Member
Registered: 22nd Feb 05
Location: Basildon, Essex
User status: Offline
|
quote:
Originally posted by fro-dizzle
I get this because i wedged my sub against it, if you kneel on the back seat press the button down with one hand and then hit it hard towards the boot it should pop free and you can pull it forward.
same here, some cursing and shoving usually gets the job done 
Drives supercharged Tec with torque  
|
ellouise9
Member
Registered: 11th Jul 07
Location: Pompey
User status: Offline
|
mine is jammed i have tried pushing the buttom and wacking hard but it wont budge i even got my dad and bf to have a shot at it but one of the bottom latch is jammed any other ideas
|
martunk2.0
Member
Registered: 14th Sep 07
User status: Offline
|
Hit it.
|
dean101287
Member
Registered: 22nd Jul 07
Location: Cardiff
User status: Offline
|
mine also did this.i took the seat out by taking the thing that goes into it from the back and then took the material off and then i could see the problem so u fixed it. mine was problem with the mechanism
|
dean101287
Member
Registered: 22nd Jul 07
Location: Cardiff
User status: Offline
|
u* I
|
Mo
Member
Registered: 29th Jan 03
Location: Bolton, Drives Q3 S-line +
User status: Offline
|
dean - so u took off the grey material on the back? was it glued on or stapled?
|
dean101287
Member
Registered: 22nd Jul 07
Location: Cardiff
User status: Offline
|
yer took the grey material off. its held on with clips that push in. i took them off with a claw hammer so i didnt wreck them. the cloth material on the front comes off easily aswell and then the foam comes off. just dont lose any of the clips that hold the material on as the tend to ping off and go flying- on mine a little bit of plastic was broken but with a bit of fiddling it now seems to work fine.
|
Mo
Member
Registered: 29th Jan 03
Location: Bolton, Drives Q3 S-line +
User status: Offline
|
cheers will have a go tomoz. knowing my luck i'll break all the clips lol
|
edwardw
Member
Registered: 10th Sep 07
User status: Offline
|
when i bought my B there were no bolts in one side of the release arm things, and it had snapped on one side so hard to pull the seat forward!
|
danward
Member
Registered: 14th Nov 06
Location: Northants Drives: C Exclusiv
User status: Offline
|
Just give it a bloody good yank!
|
