cfuk
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 2nd Jan 07
Location: Wigan
User status: Offline
|
Has anyone fitted one of these to thier car? if so what have you done with the sensor to stop the engine light from coming on? i've just have one fitted and the engine light has come on. Also could it cause my engine to over rev? the car is idel at 1000k and before it was at 900k plus when your slowing down and push the clutch in it goes up to 2000k. I've just had fitted:
Protech Manifold
Bigger Inlet (the box like ones)
FSE Fuel Valve
Quickshift Linkage
|
daz 16v
Member
Registered: 12th Jun 06
Location: Pemberton, Wigan
User status: Offline
|
could be an air leak, mine idles at 1000 but only when started.
|
Steve X16XE
Member
Registered: 31st Dec 06
Location: Barnsley, South Yorkshire
User status: Offline
|
quote:
Originally posted by cfuk
the car is idel at 1000k and before it was at 900k plus when your slowing down and push the clutch in it goes up to 2000k.
I thought this was normal 
I haven't done anything about the light being on. Might take the bulb out......
|
cfuk
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 2nd Jan 07
Location: Wigan
User status: Offline
|
well he did say that i would need a new pipe from halfords for the air sensor or w/e it is. I'll have to get one on Sunday
|
Steve X16XE
Member
Registered: 31st Dec 06
Location: Barnsley, South Yorkshire
User status: Offline
|
naa....
Just ignore it and drive fast (safely) 
|
daz 16v
Member
Registered: 12th Jun 06
Location: Pemberton, Wigan
User status: Offline
|
steve carl drives like a old women
|
cfuk
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 2nd Jan 07
Location: Wigan
User status: Offline
|
can't drive the car prove at the min  think the FSE might be putting bit more fuel in, so i need to sort that and when the car starts up it's going up and down between 800k and 500k. Could that be an air leak or something else?
|
dan-h
Member
Registered: 28th Jan 06
User status: Offline
|
have you had your FSE det up on a RR yet?
if not then do it.
|
cfuk
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 2nd Jan 07
Location: Wigan
User status: Offline
|
what? lol
i've had a look in the engine and there are some pipes doing nothing and not blocked up, could it be them?
|
Scotty C
Member
Registered: 6th Nov 05
Location: Kidderminster Drives: 1.6 16v Sport
User status: Offline
|
You need to remove the SAI motor, there is a sensor on there you need to disconnect. Don't worry about the others.
|
Dave A
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 10th Dec 03
Location: County Durham
User status: Offline
|
http://i127.photobucket.com/albums/p153/cfuk85/New%20Car/DSC00377.jpg
that one needs blocking up. and the FSE needs to be set on a rolling road so its fuelling properly.
|
cfuk
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 2nd Jan 07
Location: Wigan
User status: Offline
|
so i block this up: http://i127.photobucket.com/albums/p153/cfuk85/New%20Car/DSC00377.jpg
and take this off: http://i127.photobucket.com/albums/p153/cfuk85/DSC00375.jpg
i don't know of car rolling roads near me
|
Scotty C
Member
Registered: 6th Nov 05
Location: Kidderminster Drives: 1.6 16v Sport
User status: Offline
|
Yup.
I'm sure theres some, look around.
|
daz 16v
Member
Registered: 12th Jun 06
Location: Pemberton, Wigan
User status: Offline
|
carl theres one in hindley
|
cfuk
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 2nd Jan 07
Location: Wigan
User status: Offline
|
where abouts?
how do i take the SAI motor off proper?
|
daz 16v
Member
Registered: 12th Jun 06
Location: Pemberton, Wigan
User status: Offline
|
two 13mm bolts just holding it in place.
hyper sr its behind tesco
|
Scotty C
Member
Registered: 6th Nov 05
Location: Kidderminster Drives: 1.6 16v Sport
User status: Offline
|
Use your initiative.
|
gsirick
Member
Registered: 18th Feb 07
Location: mid-wales
User status: Offline
|
quote:
Originally posted by cfuk
Protech Manifold
Bigger Inlet (the box like ones)
FSE Fuel Valve
Quickshift Linkage
im havin an inlet like that fitted to my gsi with a enlarged v6 throttle body attached. will let u no wat its like wen its fitted
|
cfuk
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 2nd Jan 07
Location: Wigan
User status: Offline
|
right i've took the SAI motor off the and and then it keep cutting out, so i've had to put it back on the car. What am i doing wrong?
|
bubble
Member
Registered: 24th Jan 04
Location: Darwin, NT Australia.
User status: Offline
|
ur intake pipe is tiny!!!
|
cfuk
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 2nd Jan 07
Location: Wigan
User status: Offline
|
what?
|
willhouse
Member
Registered: 11th Jul 06
Location: Sheffield
User status: Offline
|
that fse valve needs destroying, or keep if fitted if you get it set up properly.
|
bubble
Member
Registered: 24th Jan 04
Location: Darwin, NT Australia.
User status: Offline
|
the intake where it goes into throttle body just before on the curve is tiny!! get that sorted out!
|
cfuk
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 2nd Jan 07
Location: Wigan
User status: Offline
|
i was tod that i need one for the sensor. I was told that i could get one from halfords, but i can't seem to find one. Any ideas of where i can get one?
i was thinking about taking it off for the time being until i can get it rolling roaded
[Edited on 22-04-2007 by cfuk]
|
cfuk
USER UNDER INVESTIGATION - DO NOT TRADE
Registered: 2nd Jan 07
Location: Wigan
User status: Offline
|
anyone?
|
