corsa_wes
Member
Registered: 7th May 07
Location: birmingham
User status: Offline
|
the door handle inside the car. ive removed the casing around it, and took the pin from in it, but its held on inside isnt it?
and the winder for the window? lol
im spraying all of it, and it looks odd with those 2 parts left grey.
oooh and the centre part of the dash board. i removed the screws and nobs etc, but not sure to get the rest away? seems as though its attached still?
|
Ricky352
Member
Registered: 6th Apr 07
Location: Northern Ireland
User status: Offline
|
The dash i dont no about, and the window winder thing is a real fuker. I think u need a specialist tool for the job, i tried removing it and cudnt and same story for my mate and his astra. The door handle is easy though. Remove the outer casing as u said uve done, then there will be a screw near the bottom of the bit u pull the door open with. U wont be able to see the screw as its very far in and may take a bita mucking about to get grip on it. There are two other screws i think, which are visible. Then remove ur tweeter just by sliding it out - simple enough
U can then just pull it off.
[Edited on 22-06-2007 by Ricky352]
|
corsa_wes
Member
Registered: 7th May 07
Location: birmingham
User status: Offline
|
lol guna have a few problems with the winder then lol
i done that dude with the handle, but the actual part u pull to open the door is attached to sumthing within the door. no wot i mean?
[Edited on 22-06-2007 by corsa_wes]
|
Ricky352
Member
Registered: 6th Apr 07
Location: Northern Ireland
User status: Offline
|
If uve unscrewed that screw that sits way in i cant see there being a problem. Wot year of car is it, mines a 1999. I had to twist and pull at mine a wee bit to get it off.
|
taty
Member
Registered: 18th Apr 07
Location: Berwick-upon-Tweed, Northumberland
User status: Offline
|
you have to pull down the heater vents and there is screws behind them
undo them and it should come lose
then you have to reach behind and unclip the wires and it should come away
|
taty
Member
Registered: 18th Apr 07
Location: Berwick-upon-Tweed, Northumberland
User status: Offline
|
and to get the winder off i just used a presion screwdriver to unclip the thing holding it on
and you can do it with a rag get it behind and pull it back and forwards and that should unclip it
|
corsa_wes
Member
Registered: 7th May 07
Location: birmingham
User status: Offline
|
bang on mate, i'll have another go over the weekend, hopefully manag to do it.
already sprayed the door parts, looks good 
|
GSi Ghost
Member
Registered: 15th Dec 05
Location: Stoke-on-Trent
User status: Offline
|
To get the window winder off I used a rag to pull the clip off; works a charm just have to pull the rag fromn side to side and it will eventually pop off. But be ready cuz most the time it flys a fookin mile!!!
|
paul.mitchell1984
Member
Registered: 31st Aug 06
Location: Wakefield
User status: Offline
|
bit of wire with a a small bend in the end, lever it out sdo u can see clip then twist wire underneath and lift Easiest way 2 min job ,
when u say handle do you mean to open or just the pull ahndle as pull handle has 3 screws thats it, the opener u need to take inner door card off disconect the wire and it slides out (towards front of car)
centre console two more screws behind heater fans
|
Mark.W
Member
Registered: 3rd Jan 07
Location: County Durham
User status: Offline
|
iv just removed my window winder today,the old rag trick done the job for me,but when fitten it back together you will get a sligtly bigger gap between the door card and the winder but its not too bad hardly notice it.
|
STEvieXE
Member
Registered: 21st Jan 03
Location: Ballymena N.I.
User status: Offline
|
in the door handle u mean the part the actual handle is attached to slide it back...
|
