|
Not logged in [Login - Register] |
You Are Not Registered Or Not Logged In |
Corsa Sport » Message Board » Help Zone, Modification and ICE Advice » dash screws » Post Reply
|
j0hn |
posted on 8th Dec 04 at 12:19 |
got 4 new bearings and new rear axle!!! all on apparently its my girlfriends dads whos done it out of kindness of his heart..fuck knows wot i shud get him for xmas now!!! ARRRGH BEING A STUDENT SUXXXS!!! | |
Russ |
posted on 8th Dec 04 at 07:59 |
mate, i think you need a new hobby :| | |
j0hn |
posted on 8th Dec 04 at 00:26 |
so cud fix it yeah or need new one?? -this just in - car's wheel bearings have ALL gone!!! wrong offset rims given way cos of stress garage sed | |
cobra148 |
posted on 7th Dec 04 at 13:08 |
quote: If you have a soldering iron, pass the tip across the pins where they join the circuit, these things are vry fragile and only have a little solder on them from the factory. Repeated plugging/unplugging may have caused a break in the joint, common problem if mfd is taken out a few times. | |
PaulW |
posted on 7th Dec 04 at 13:05 |
on the MFD itself??? | |
j0hn |
posted on 7th Dec 04 at 12:52 |
MFD connector is all loose iv unplagged and plugged it in too many times.. so now intermittant! Wot shud i do??? Anyone?? | |
cobra148 |
posted on 2nd Dec 04 at 18:45 |
Bulb paint is a total waste of time, it WILL eventually burn off and change colour. | |
j0hn |
posted on 2nd Dec 04 at 13:14 |
lol no iv not poured paint into the MFD!!! All i did was paint bulbs and then they wer dry wen i put them back into mfd lmao | |
ed |
posted on 1st Dec 04 at 18:55 |
You pored paint into it. Not good. Fucked MFD. Buy a new one. | |
j0hn |
posted on 1st Dec 04 at 18:49 |
??? | |
j0hn |
posted on 1st Dec 04 at 12:12 |
no loose conections any1 had this? | |
j0hn |
posted on 30th Nov 04 at 19:32 |
HELP??? | |
j0hn |
posted on 30th Nov 04 at 18:58 |
its flashing now (MFD) ???? really confused | |
PaulW |
posted on 30th Nov 04 at 15:57 |
check make sure the wiring is plugged back in securely & there are no wires which have come loose | |
j0hn |
posted on 30th Nov 04 at 15:50 |
again need help | |
j0hn |
posted on 30th Nov 04 at 14:01 |
BULBS PAINTED! :( Went tis up put too much laquer on one and one bulb in MFD died somehow in process and MFD now resets every time i turn on main beam lights and turn them off!!! ARGH ANY HELP REQUIRED | |
Adam-D |
posted on 26th Nov 04 at 21:17 |
dials theres 1 either side of the cowling 1 up insode the centre of the cowling | |
j0hn |
posted on 26th Nov 04 at 21:10 |
???? | |
j0hn |
posted on 26th Nov 04 at 19:57 |
fuck i really cudnt get dash speedo out!!! 3 screws anymore??? | |
j0hn |
posted on 26th Nov 04 at 13:43 |
wel im going to paint my bulbs in dash and MFD, i kno how to take apart the mfd and get to the 3 bulbs on heater controls but wer r the other bulbs ontained in dash cos i not taken this part away before!! |