corsasport.co.uk
 

Corsa Sport » Message Board » General Chat » Quick Turbo Question!! (re: Inlet temps + i/c water spray)


New Topic

New Poll
  <<  1    2  >> Subscribe | Add to Favourites

You are not logged in and may not post or reply to messages. Please log in or create a new account or mail us about fixing an existing one - register@corsasport.co.uk

There are also many more features available when you are logged in such as private messages, buddy list, location services, post search and more.


Author Quick Turbo Question!! (re: Inlet temps + i/c water spray)
MattyB
Member

Registered: 13th Nov 01
Location: 118.5bhp :D
User status: Offline
27th Dec 03 at 00:29   View User's Profile U2U Member Reply With Quote

Could someone please help me out quickly......i'm looking into gettin an inlet temp gauge on my pug....but need to find out summat........

........All i need to know is whats the sort of MAXIMUM temp i'm gonna experience in the pipes leading away from my intercooler at full boost (1.2 bar spun by a garrett t2 if that makes any difference)

This would need to be roughly 20cm AFTER the I/C

cheers

Matt

[Edited on 27-12-2003 by MattyB]
AK
Member

Registered: 5th Jul 00
Location: Aberdeen City
User status: Offline
27th Dec 03 at 00:47   View User's Profile U2U Member Reply With Quote

why do you want to measure inlet temp

EGT's are much much much more usefull
MattyB
Member

Registered: 13th Nov 01
Location: 118.5bhp :D
User status: Offline
27th Dec 03 at 01:04   View User's Profile U2U Member Reply With Quote

Coz basically i wanna do some testing!! And just outta curiousity as well

However, the main areas i like to see the temp differences would be after i've fitted.....

*larger i/c
*bonnet vent
*Water injection
*type of induction i use

So wot do u recon the max inlet temp i'll see is? 80-100? degrees C in standard form?

Matt
J da Silva
Member

Registered: 10th Apr 03
Location: The FACTory
User status: Offline
27th Dec 03 at 01:07   View User's Profile U2U Member Reply With Quote

90ish by textbook
Adam
Member

Registered: 1st May 01
Location: Hurstbourne Tarrant
User status: Offline
27th Dec 03 at 01:51   View User's Profile U2U Member Reply With Quote

a water spray on the intercooler can drop it as much as 7 degrees
MattyB
Member

Registered: 13th Nov 01
Location: 118.5bhp :D
User status: Offline
27th Dec 03 at 02:02   View User's Profile U2U Member Reply With Quote

"Every drop of 4 degrees, has the potential to unleash 1+ bhp"

I was just reading on some Kiwi forum that this guy managed to get his temps down 19 degrees using water injection onto his 2.8 Pajero TD I/C

Matt
AK
Member

Registered: 5th Jul 00
Location: Aberdeen City
User status: Offline
27th Dec 03 at 03:14   View User's Profile U2U Member Reply With Quote

..... then you melt a piston

not so much an issue on TD's like.... but still

MattyB
Member

Registered: 13th Nov 01
Location: 118.5bhp :D
User status: Offline
27th Dec 03 at 12:51   View User's Profile U2U Member Reply With Quote

so........anyone got any info on water injection (on intercooler)

Is it worth it? will it make a noticeable difference? Am i better off just leaving it with a vent?

Matt
Adam
Member

Registered: 1st May 01
Location: Hurstbourne Tarrant
User status: Offline
27th Dec 03 at 13:07   View User's Profile U2U Member Reply With Quote

http://www.roesser.com/wrx_intercool.asp

http://www.autospeed.com/cms/article.html?&C=articles&A=0527&P=1

http://www.google.com/search?hl=en&ie=UTF-8&oe=UTF-8&q=diy+intercooler+waterspray
MattyB
Member

Registered: 13th Nov 01
Location: 118.5bhp :D
User status: Offline
27th Dec 03 at 13:12   View User's Profile U2U Member Reply With Quote

yes..........been reading up on it for hours, seems a very simple idea...and in some cases, very worth while........

waht u reckon Adam? (all these examples seem to be on high power scoobies etc)
Adam
Member

Registered: 1st May 01
Location: Hurstbourne Tarrant
User status: Offline
27th Dec 03 at 13:18   View User's Profile U2U Member Reply With Quote

for £50 work of parts seems worth it to me
Drew
Banned

Registered: 24th Nov 01
Location: County Durham
User status: Offline
27th Dec 03 at 13:22   View User's Profile U2U Member Reply With Quote

quote:
Originally posted by MattyB
so........anyone got any info on water injection (on intercooler)

Is it worth it? will it make a noticeable difference? Am i better off just leaving it with a vent?

Matt


i know a lad with a scooby....

on the rollers it lost bhp with the water injection on to it turned off, but supposedly its better on the road - think he took it off thou

MattyB
Member

Registered: 13th Nov 01
Location: 118.5bhp :D
User status: Offline
27th Dec 03 at 13:25   View User's Profile U2U Member Reply With Quote

I'm gonna go for it!! off down scrappy to source some test bits + bobs and set up a test system indoors etc

keep u posted

Need to get me a temp sensor as well!

Matt
vibrio
Banned

Registered: 28th Feb 01
Location: POAH
User status: Offline
27th Dec 03 at 16:32   View User's Profile U2U Member Reply With Quote

forget about water injection. waste of cash.
MattyB
Member

Registered: 13th Nov 01
Location: 118.5bhp :D
User status: Offline
27th Dec 03 at 16:45   View User's Profile U2U Member Reply With Quote

I'm just gonna make a cheapo little set up, and see how it goes.

but i need to sort out a inlet temp thingy first, so i can actually note the kinda difference its made!! if its reasonable, i might do it proper!

Altho i doubt anything will be better than using a bigger i/c and/or a vent

Matt
vibrio
Banned

Registered: 28th Feb 01
Location: POAH
User status: Offline
27th Dec 03 at 16:50   View User's Profile U2U Member Reply With Quote

it's easy to set up an inlet temp. get two probes one pre intercooler one post intercooler. then get a digital gauge which alows you to switch between temps. then start recording
Stu
Member

Registered: 3rd May 00
Location: Madchester UK Drives: 2014 BMW M135i
User status: Offline
27th Dec 03 at 17:03   View User's Profile U2U Member Reply With Quote

On the Nissan 200sx - standard intercooler was seeing inlet temps of up to 90 degrees, with the front mount these dropped as low as 29 degrees (that was on the rollers too!) As Vibs said all you need are temp sensors on the intercooler pipework of the car, thats it! I think Halfords do some temp sensors?

As far as the water spray goes, again on the 200sx I used the pipe work and motors of the washers for the headlamps. Basically disconnted the piping going to them, put Fiat Conquecento washer jets (3 jets) on the bumper either side of the intercooler and jobs a good one.

As far as how well it worked? To be honest, if it had been any more difficult than it was (ie p*ss easy!) I really wouldnt have bothered. Gains are gonna be minimal and who wants to try and press a little button when they are thrapping along!? Good for the novelty value though?

You may also have problems with the IC being on top of the engine too? Unless done properly itll soak your engine everytime you squirt it!

Hope that helps?
MattyB
Member

Registered: 13th Nov 01
Location: 118.5bhp :D
User status: Offline
27th Dec 03 at 17:11   View User's Profile U2U Member Reply With Quote

Stu - very good points there, cheers.

Vibs (or anyone else) - where could i get a pair of temp sensors??? I've looked in maplin, local motor factors, halfords etc and i cant see any that would do the job.

The only ones i have found can only read up to 60 degrees

Any ideas? any online stores that would do such a thing?

cheers!

Matt
vibrio
Banned

Registered: 28th Feb 01
Location: POAH
User status: Offline
27th Dec 03 at 17:11   View User's Profile U2U Member Reply With Quote

GT shows inlets of 60c with FMIC it is down to 20c
MattyB
Member

Registered: 13th Nov 01
Location: 118.5bhp :D
User status: Offline
27th Dec 03 at 17:51   View User's Profile U2U Member Reply With Quote

Bit i've not got a clue as to what mine will show as it is now, and ideally, i think sensors that show up to bout 80degrees would be better

Matt
Stu
Member

Registered: 3rd May 00
Location: Madchester UK Drives: 2014 BMW M135i
User status: Offline
27th Dec 03 at 20:30   View User's Profile U2U Member Reply With Quote

Yeah, with your cooler being mounted on top of the engine (like the one on my P1) I think youll find your inlet charge peaks in traffic will be quite high - you may even see over 90 degrees?

Try http://www.apex-performance.co.uk I know Bren from Apex has temp sensors suitable for the 200sx but as far as I can tell they are all gonna work on the same principal. All youll need is an airtight hole in your selected I/C pipe. Whether it be a flexible hose or something braised into the hard pipes.

Let us know how you get on, I reckon it will be quite interesting to see the different changes in charge air temp in different situations.
vibrio
Banned

Registered: 28th Feb 01
Location: POAH
User status: Offline
27th Dec 03 at 20:53   View User's Profile U2U Member Reply With Quote

you can hook one up for afew quid. no need to go over board
MattyB
Member

Registered: 13th Nov 01
Location: 118.5bhp :D
User status: Offline
28th Dec 03 at 14:02   View User's Profile U2U Member Reply With Quote

quote:
Originally posted by vibrio
you can hook one up for afew quid. no need to go over board


but it does need to be accurate, and a decent set up that runs off 12v.

I want it to be a permanent feature on my dash you see.

Stu - will keep u posted mate

Matt

MattyB
Member

Registered: 13th Nov 01
Location: 118.5bhp :D
User status: Offline
28th Dec 03 at 15:59   View User's Profile U2U Member Reply With Quote

hmmm been lookin all day on the net for some1 that can tell me the maximum charge temps i'm gonna see on my Pug......

hmmmm
vibrio
Banned

Registered: 28th Feb 01
Location: POAH
User status: Offline
28th Dec 03 at 17:00   View User's Profile U2U Member Reply With Quote

probably around 65-70C at the most.

  <<  1    2  >>
New Topic

New Poll

Corsa Sport » Message Board » General Chat » Quick Turbo Question!! (re: Inlet temps + i/c water spray) 22 database queries in 0.1820798 seconds