andyw1986
Member
Registered: 30th Nov 08
Location: stoke on trent
User status: Offline
|
alright folks
how do i fit the rear bench and backrests to my corsa.
just tried get tehm in and they go no where near so instead of loosing my head and chucking them in the fookin bin i though id ask here for help.
any suggestions guides help appreciated.
nice 1
andy
[Edited on 15-02-2009 by andyw1986]
|
dean101287
Member
Registered: 22nd Jul 07
Location: Cardiff
User status: Offline
|
REAR SEATS
TAKING THE OLD SEATS OUT:
To fit the rear calli leather seats you will need to have a 60/40 split backrest. Assuming that you have, I started by taking the original corsa rear seats out (both parts). To take out the base part lift it up and there is a bracket at either end with a screw in, undo the screws and with a bit of pulling and pushing the base should come out.
Next job is to go into the boot. On the back of the back rests there sould be some plastic covers (one at iether side). Take these off and there will be two bolts under each one. Take all 4 of these out and the back rests should come out. The Backrests should come out after that. I cant remember if there are any bolts are in the middle section though but you'll be able to see these if there are. I found having a haynes manual was useful for taking out the back seats. I think their example is from a post 97 corsa. The description i just gave you is from a pre 97 corsa and there are some slight differences. Also when you're doing the back rests some parts might be easier with the seats up and some parts with the seats down.
BACK RESTS:
Now you have your old seats out, I started with the back rests first. Take you old corsa back rest and flip it over so youre lookig at the carpeted side that was in the boot. Start at the bottom and undo all the little plastic stoppers (a flat bladed screw driver comes in handy for this). Once all these are undone the carpet can be lifted up (its still attached at the top tho) and the metal frame of the seat can be seen. At the edges you will see where the material is tucked over and secured. Use a flat blade screw driver to pull it out. After this it will be held on by the button at the top for putting the seat down. Pull the material over this and it should come off, with the padding as well.
Repeat this process on the calli back seats. The reason for this is that the calli frames wont fit in the corsa brackets. Now reverse the process to fit the leather and the calli padding onto the corsa frames. I found it was easier to start by putting the leather(and padding if needs be) over button (for dropping the seats) and then hooking the 3 edges over after that. The calli padding is alot bigger than the original corsa padding so its very tight. Just keep at it and eventually the padding will fit.
NOTE: When this is done the carpet on the back will not fit the base as its a different shape
THE BASE
Alot of people on here have just put the calibra base in and left it at that but I personally found that because of different shapes in the floors from the two cars, the back bench sits very high in a corsa so i decided to take the leather off and put it on my corsa bench. I started by turning the calli bencch over. Theres are metal all the way around holding the leather onto the padding/frame. I undid all of these with a screwdriver. When they are all off, the leather will coem off the base quite easily. After that I put it over the original corsa seat and used some strong string to to hold it on, making a criss cross pattern on the underside of the seat. The only draw back of this is that it leaves the leather very saggy but its really comfy. My advice would be to try putting in the calli bench first and see what you think.
RE-FITTING THE SEATS
I found it easier to put the back rests in first. It will be a tight fit but it will all go in snug. Just reverse the method used to take them out.
When i reffited my bench (bear in mind it was original corsa bench not the calli) I screwed the two brackets back in and pushed the seat down. Again this is very tight so just keep pushing and youre done.
|
dean101287
Member
Registered: 22nd Jul 07
Location: Cardiff
User status: Offline
|
Taken from tutorials
|
andyw1986
Member
Registered: 30th Nov 08
Location: stoke on trent
User status: Offline
|
legend mate thats helps alot thanks. looks like ill be scouring scrappys for a seat of rear corsa seats now
|
XSIHardy
Member
Registered: 5th Feb 08
User status: Offline
|
Are you trying to get the rear seats in yes?
if so just keep going for it they go in trust me, its a fair amount of pissing around but you will get there 
[Edited on 15-02-2009 by XSIHardy]
|
andyw1986
Member
Registered: 30th Nov 08
Location: stoke on trent
User status: Offline
|
cant get the bench in but its different shape so ill probably just make a plate up to fasten them to at work tomorrow.
its just the backrests there totally different and i aint got any standard corsa seats at the mo i can transfer them to lol
|
XSIHardy
Member
Registered: 5th Feb 08
User status: Offline
|
mmm i didnt change any thing when fitting mine, just fitted them straight in there, bit tight but all gravy. have you fitted the front seats yet?
[Edited on 15-02-2009 by XSIHardy]
|
andyw1986
Member
Registered: 30th Nov 08
Location: stoke on trent
User status: Offline
|
yeah front seats peice of piss do u have any pics of your rears mate????? desperately need help lol
|
Archie
Organiser: Scotland
Premium Member
Registered: 18th Dec 07
Location: South Ayrshire
User status: Offline
|
I got annoyed and threw mine out.
|
fightstar
Member
Registered: 14th Nov 08
User status: Offline
|
i got a 5dr, to for back i did this, the back rest went straight in, to fit the bum rest, i took leather of the calibra bech, and put it over my old bum rest, used the hook string etc, to hold it all together, looks mint took about 45mins
|
andyw1986
Member
Registered: 30th Nov 08
Location: stoke on trent
User status: Offline
|
any pics mate the backs on the 3dr didint look like they went anywhere near>???
|
adz_gsi
Member
Registered: 20th Sep 08
User status: Offline
|
i can fitthese if ya want m8 i did reaudioxxx S rear for him not that hard really
|
fightstar
Member
Registered: 14th Nov 08
User status: Offline
|
Might be some on my project thread http://www.allcorsa.co.uk/forums/showthread.php/my-corsa-1-10583p15.html
can't look gotta pop out mate
|
andyw1986
Member
Registered: 30th Nov 08
Location: stoke on trent
User status: Offline
|
adz gsi yeah mate if you could what do i need for you to fit them mate???
|
