|
Not logged in [Login - Register] |
You Are Not Registered Or Not Logged In |
Corsa Sport » Message Board » General Chat » Help with MFD for my corsa b » Post Reply
|
3lfz |
posted on 5th Jun 09 at 08:40 |
quote: | |
FAZ |
posted on 5th Jun 09 at 08:31 |
haynes corsa modifying manual is a good tutorial | |
DaveyLC |
posted on 5th Jun 09 at 08:11 |
No screws.. :) | |
*JonnyG* |
posted on 4th Jun 09 at 23:13 |
They have screws? Oh... I just pulled the fuckers off. | |
Jamxe |
posted on 4th Jun 09 at 23:07 |
Gonna have to just stick flat head by the side and leaver it off (put a rag on the screwdriver so as to not mark the facia) and just force it off.. Sort out whatever damage is done after.. or else just leave em alone.. :D | |
DaveyLC |
posted on 4th Jun 09 at 23:03 |
Eat some shreddies and try again! | |
CorsaJack1 |
posted on 4th Jun 09 at 16:32 |
this dial must be glued, i gave it the biggest manlyest pull ever and jus stays there | |
Jamxe |
posted on 4th Jun 09 at 15:16 |
quote: :lol::lol::thumbs: | |
DaveyLC |
posted on 4th Jun 09 at 15:09 |
And that dial does just pull out.. Give it a manly pull! | |
DaveyLC |
posted on 4th Jun 09 at 15:09 |
quote: You need to remove the whole thing.. Tilt the top vents foward and release the screws behind, then pull off the recirc slider and the facia behind it to uncover the two lower screws, remove the hazard light switch and lever the connector inside the panel downwards (so it drops out), the panel will then come away.. You need to disconnect the fan switch loom and un do all of the vent control wires... Now you can remove the panel and access the torx bolts that hold the bulb carrier to the back of it :thumbs: | |
adz_gsi |
posted on 4th Jun 09 at 14:57 |
where are you mate i could do it if close | |
Jamxe |
posted on 4th Jun 09 at 14:53 |
On my 99 Sport I had to take the whole thing apart.. 3 Dials off, and black plastic facia.. No other way to get into them.. Never bothered doing them in my 96 corsa but the dials were definatly easier to get off.. Strip that muther dude..:lol: | |
CorsaJack1 |
posted on 4th Jun 09 at 14:25 |
sorry the fan/heater controls | |
DaveyLC |
posted on 4th Jun 09 at 14:20 |
Are you talking about the MFD or the Heater/Fan controls? | |
CorsaJack1 |
posted on 4th Jun 09 at 14:18 |
im replacing the LED's that light up the 3 dials on the heater/fan controls, do i not need to take these dials off? because the guide it came if was very bad | |
mike r |
posted on 4th Jun 09 at 13:55 |
If your just replacing the lights at the back the haynes is wrong you dont need to take the middle switch out, i did the first time and broke it, just take undo the 4 screws and pull it out the heater console, | |
Jamxe |
posted on 4th Jun 09 at 11:37 |
Yeah just push a flathead in there and pull the knob off at the same time.. Problem is someone before you might have broken it and glued it back on :o | |
CorsaJack1 |
posted on 4th Jun 09 at 11:21 |
iv been poking a screwdriver in the little whole for some hours now and still no luck :( | |
FruitBooTeR |
posted on 4th Jun 09 at 10:43 |
It does just pop off just keep trying :thumbs: | |
CorsaJack1 |
posted on 4th Jun 09 at 10:34 |
Hi, |