|
|
|
Not logged in [Login - Register] |
 |
You Are Not Registered Or Not Logged In |
|  |
|
Corsa Sport » Message Board » Help Zone, Modification and ICE Advice » Dial Removing » Post Reply
|
| the_legend_of_yrag |
posted on 11th Sep 03 at 18:48 |
Just wait till i have a go at mine, will be a nightmare i know. Was a nightmare gettin the centre out, gave up in the end! | |
| R Lee |
posted on 11th Sep 03 at 17:10 |
sheesh... it wasn't that tough when i did mine :boggle: | |
| BigSte |
posted on 11th Sep 03 at 17:08 |
ye, there is nothin at all holdin it down. I'll go try again | |
| cobra148 |
posted on 11th Sep 03 at 17:05 |
Thats right, just keep pulling on it, it will come eventually :lol: | |
| Adam-D |
posted on 11th Sep 03 at 16:13 |
just wiggle it pull it itll come out | |
| cobra148 |
posted on 11th Sep 03 at 16:10 |
Steve, the shroud is loose and moves freely I assume, theres nothing else to physically hold it on now the screws are out. Go eat three shredded wheat and have another pop at it. | |
| BigSte |
posted on 11th Sep 03 at 15:42 |
I think its just me beein a flid......i'll have another go n if that doesnt work the axe is comin out | |
| R Lee |
posted on 11th Sep 03 at 15:35 |
quote: hammer :lol: why not... if that still wont do, use a chainsaw, mind the steering wheel though :lol: | |
| cobra148 |
posted on 11th Sep 03 at 15:33 |
Thats right, lift it towards you and up at the same time, should lift out with no probs if those other screws are out, theres nothing else holding it in. Take a hammer to it ;) | |
| BigSte |
posted on 11th Sep 03 at 15:28 |
tried mate for aaaaaaages and cant do it. my mates gonna have a go later. he's done his own | |
| R Lee |
posted on 11th Sep 03 at 15:26 |
quote: i cant remeber exactly on my old car... but dont you just lift it upand towards you? | |
| BigSte |
posted on 11th Sep 03 at 15:21 |
Yes done that and removed the bottom half (no air bag wheel btw) | |
| cobra148 |
posted on 11th Sep 03 at 14:09 |
Steve, on the steering colum shroud (the 2 piece part directly behind the wheel) I assume you have turned the wheel to the left, removed the plasic cap and removed the screw? Then turn the wheel right and do the opposite side. Then take out the screw in the bottom half of the shroud, in the recess underneath, you have done this ..yes? | |
| R Lee |
posted on 11th Sep 03 at 12:30 |
quote: do you mean the steering column bit? | |
| Adam-D |
posted on 11th Sep 03 at 12:28 |
u lift the front of the igniton top bit up | |
| BigSte |
posted on 11th Sep 03 at 12:24 |
I just cant get the dial surround and the plastic at the top of the ignition switch out | |
| R Lee |
posted on 11th Sep 03 at 12:06 |
quote: if i can remeber right... all i did was try and wiggle the pod out. is this what you mean? | |
| BigSte |
posted on 11th Sep 03 at 11:50 |
??? | |
| BigSte |
posted on 11th Sep 03 at 11:21 |
how do u uncip them? | |
| t44rnt |
posted on 11th Sep 03 at 11:15 |
u gotta unclip the indicator lever and the window wiper lever, the the top bit shoudl come off to the left easily | |
| BigSte |
posted on 11th Sep 03 at 11:14 |
Right I'm wanting to take my dials out to replace the bulbs but have a slight problem. I have removed every screw from the plastic dial surround and all the screws from the ignition surround. I have taken the bottom half of the ignition surround off but can't get the top half or the actual dial sourround out. |
