|
Not logged in [Login - Register] |
You Are Not Registered Or Not Logged In |
Corsa Sport » Message Board » Help Zone, Modification and ICE Advice » oops, Help broke connector on interior wiring loom » Post Reply
|
jr |
posted on 15th Jul 06 at 17:17 |
done :D | |
flash22 |
posted on 15th Jul 06 at 16:55 |
in the plug with the ignition wires coming out off it theres a square hole put a screw driver in it as theres a tag/clip that you need to push in normally you would have the key in the barrel in pos 1 in this case just need to move the centre bar around to line up the groove on the bar so the tag/clip goes into the groove it then releases the plug from the switch. yo may need to leaver in apart tho its hard to explain realy | |
jr |
posted on 15th Jul 06 at 16:48 |
when you say "push the tag in leaver the plug/switch off job done !!!!" | |
flash22 |
posted on 15th Jul 06 at 16:42 |
you just need to take the rest of the old switch off spin the centre post around till the groove in in th right place then push the tag in leaver the plug/switch off job done !!!! | |
jr |
posted on 15th Jul 06 at 16:38 |
found it, didnt realise there actully sealed with paint (red in this case) | |
flash22 |
posted on 15th Jul 06 at 16:31 |
it's in the front and one in the back that holds the ignition switch its about 3-4mm flat head abut 3-4 from the edge of the switch | |
jr |
posted on 15th Jul 06 at 16:29 |
where is the grubscrew though ??? | |
RobHayes |
posted on 15th Jul 06 at 16:23 |
just take the lock barrel off and have a switches instead of a key :look: | |
flash22 |
posted on 15th Jul 06 at 16:17 |
i was right youve kill the ignition switch new one required!!! thay never work right if you rebuild them theres 3 springs and 2 contacts in there and the contacts are different aswell the switch is £15-20 from vx or a quid down the breakers or free if you like | |
flash22 |
posted on 15th Jul 06 at 16:15 |
sounds like yo have killed the ignition switch the switch is held on by a grub screw at the front an a pin at the back undo the grub screw and give it a twist | |
jr |
posted on 15th Jul 06 at 16:14 |
no not yet, the part which is missing houses to two pins in, which turn and make contact with the bits you see in the 2nd pic | |
Greg_M |
posted on 15th Jul 06 at 16:12 |
Have you taken the lock barrel out at all? if not take the lock barrel out, i think what youve broken is the part which the lock turns, to switch on the ignition live, but im not entirly sure. | |
jr |
posted on 15th Jul 06 at 16:07 |
| |
Greg_M |
posted on 15th Jul 06 at 15:58 |
If youve just broken the suround it might go back together, cant remember of the top of my head, but i would solder a new plug on it tbh. | |
jr |
posted on 15th Jul 06 at 15:50 |
yes greg, i still have all the wires etc on on bit in the back on the plu on the loom, the bit where it broke is where the two pins sit in, which is still on the barrell | |
Greg_M |
posted on 15th Jul 06 at 15:47 |
it is the plug that goes to the back of the barrel? | |
jr |
posted on 15th Jul 06 at 15:45 |
:thumbs: ok | |
Greg_M |
posted on 15th Jul 06 at 15:39 |
the ignition barrel JR | |
jr |
posted on 15th Jul 06 at 15:37 |
in the front of what ainsley | |
ainsley_brader |
posted on 15th Jul 06 at 15:24 |
theres a screw in the front to remove then a roll pin in the back to knock all the way in! | |
jr |
posted on 15th Jul 06 at 15:14 |
:lol: | |
Dave A |
posted on 15th Jul 06 at 11:35 |
black tape, cable ties and blue tack. Usually works for me | |
jr |
posted on 15th Jul 06 at 11:29 |
While removing the loom broke the connector that goes onto the ignition barrell/ignition switch |