|
Not logged in [Login - Register] |
You Are Not Registered Or Not Logged In |
Corsa Sport » Message Board » Help Zone, Modification and ICE Advice » corsa cv joint » Post Reply
|
Jam666 |
posted on 2nd Sep 08 at 18:30 |
ill go with a calibra one and hope for the best :thumbs: | |
DAZ1985 |
posted on 2nd Sep 08 at 18:26 |
Im lost now | |
Torsa g |
posted on 2nd Sep 08 at 18:10 |
im confused at this, its not possible | |
Jam666 |
posted on 2nd Sep 08 at 18:04 |
rite just been outside to look, the drivers side looks the same as the top shaft in the pic. but the pass side on which i need looks like the same type of shaft (goes from small to thick then back to small, but the thick bit is only about 4-5 inches long) i changed the inner joint on the passenger side a couple of weeks ago and i used a calibra joint..i just wana get the right one before i take it apart, cos i dont hav a garage or drive so will be doin it on the road | |
DAZ1985 |
posted on 2nd Sep 08 at 17:51 |
top equal length shaft may fit but you will still need the hubs to take the cvs | |
Jam666 |
posted on 2nd Sep 08 at 17:49 |
mine ar like this | |
DAZ1985 |
posted on 2nd Sep 08 at 17:44 |
The shafts wont fit then and iirc calibra shafts are 20mm longer than corsa shafts | |
Jam666 |
posted on 2nd Sep 08 at 17:40 |
no | |
DAZ1985 |
posted on 2nd Sep 08 at 17:38 |
Have you got conversion hubs? | |
Jam666 |
posted on 2nd Sep 08 at 17:37 |
i think ill cancel that order and get a calibra one :D | |
DAZ1985 |
posted on 2nd Sep 08 at 17:28 |
corsa cv wont fit a big block calibra shaft | |
Jam666 |
posted on 2nd Sep 08 at 17:00 |
i dunno, ive ordered a corsa 22 spline joint, just hope its the right one | |
DAZ1985 |
posted on 2nd Sep 08 at 16:50 |
32 spline? | |
Jam666 |
posted on 2nd Sep 08 at 16:35 |
calibra i think, they are fat as fuk | |
DAZ1985 |
posted on 2nd Sep 08 at 16:21 |
when you say ecotec shafts? off what engine? | |
Jam666 |
posted on 2nd Sep 08 at 15:59 |
ttt | |
Jam666 |
posted on 1st Sep 08 at 20:25 |
up | |
Jam666 |
posted on 1st Sep 08 at 17:56 |
ttt | |
Jam666 |
posted on 1st Sep 08 at 16:32 |
is this definatley right cos ive noticed that theres alot of thread coming trough where the joint is bolted to the hub | |
Jam666 |
posted on 31st Aug 08 at 20:51 |
ok cheers mate thanks | |
Torsa g |
posted on 31st Aug 08 at 20:50 |
yes u can use the corsa bearings, and as for the calibra cv im not to sure about that | |
Jam666 |
posted on 31st Aug 08 at 20:47 |
ok thanks, so does that mean i can use normal corsa bearings too? arnt the 22 spline gsi ? and also i changed an inner cv joint not so long ago and i used a calibra one ?? | |
Torsa g |
posted on 31st Aug 08 at 20:44 |
u will need corsa outer joints 22spline(GSI) shafts and 1.6 cav inners | |
Jam666 |
posted on 31st Aug 08 at 20:02 |
wat outer cv joint would i need for my xe corsa? ive got ecotec shafts! |