ill go with a calibra one and hope for the best :thumbs:

Im lost now





I give up :lol:

im confused at this, its not possible

rite just been outside to look, the drivers side looks the same as the top shaft in the pic. but the pass side on which i need looks like the same type of shaft (goes from small to thick then back to small, but the thick bit is only about 4-5 inches long) i changed the inner joint on the passenger side a couple of weeks ago and i used a calibra joint..i just wana get the right one before i take it apart, cos i dont hav a garage or drive so will be doin it on the road

top equal length shaft may fit but you will still need the hubs to take the cvs

bottom ebay link

mine ar like this
http://i277.photobucket.com/albums/kk45/jam0666/shaft.jpg

The shafts wont fit then and iirc calibra shafts are 20mm longer than corsa shafts

You need either
corsa outer joints 22spline(GSI) shafts and 1.6 cav inners as torsa said. they will fit your hubs

http://cgi.ebay.co.uk/corsa-td-drive-shafts-conversion-c20xe_W0QQitemZ170257680859QQcmdZViewItem?hash=item170257680859&_trkparms=72%3A985%7C39%3A1%7C66%3A2%7C65%3A12%7C240%3A1318&_trksid=p3286.c0.m14

or

Conversion shafts with mtech type hubs and big block calibra cvs

http://cgi.ebay.co.uk/VAUXHALL-CORSA-NOVA-CONVERSION-DRIVESHAFT_W0QQitemZ230214991999QQcmdZViewItem?hash=item230214991999&_trkparms=72%3A985%7C39%3A1%7C66%3A2%7C65%3A12%7C240%3A1308&_trksid=p3286.c0.m14
with
http://cgi.ebay.co.uk/VAUXHALL-NOVA-CORSA-B-2-0-XE-LET-CONVERSION-HUB_W0QQitemZ160277589087QQcmdZViewItem?hash=item160277589087&_trkparms=72%3A985%7C39%3A1%7C66%3A2%7C65%3A12%7C240%3A1318&_trksid=p3286.c0.m14

[Edited on 02-09-2008 by DAZ1985]

no

Have you got conversion hubs?

ie M-tech?

i think ill cancel that order and get a calibra one :D

corsa cv wont fit a big block calibra shaft

i dunno, ive ordered a corsa 22 spline joint, just hope its the right one

32 spline?

calibra i think, they are fat as fuk

when you say ecotec shafts? off what engine?

thiers alot of small block and big block ecotecs

ttt

up

ttt

is this definatley right cos ive noticed that theres alot of thread coming trough where the joint is bolted to the hub

ok cheers mate thanks

yes u can use the corsa bearings, and as for the calibra cv im not to sure about that

ok thanks, so does that mean i can use normal corsa bearings too? arnt the 22 spline gsi ? and also i changed an inner cv joint not so long ago and i used a calibra one ??

u will need corsa outer joints 22spline(GSI) shafts and 1.6 cav inners

some of the ecotecs are 22 spline and some arent

[Edited on 31-08-2008 by Torsa g]

wat outer cv joint would i need for my xe corsa? ive got ecotec shafts!
:thumbs: