|
Not logged in [Login - Register] |
You Are Not Registered Or Not Logged In |
Corsa Sport » Message Board » Help Zone, Modification and ICE Advice » exhaust and rear axle » Post Reply
|
ali_corsa |
posted on 28th Apr 08 at 06:27 |
No dont really know it well at all, a garage couldnt fix it as im at the college in armthorpe frm 8:30 till 5, take it for a drive tonight and see how the car runs. | |
chris_rosso |
posted on 27th Apr 08 at 17:05 |
Do you know donny much? quite a few places that wud sort ur exhaust out probly no more than a tenner. I ad egr valve go on mine n as soon as i got i fixed lambda sensor went, then airflow meter went n then icv went aswel so i know wot u mean lol | |
ali_corsa |
posted on 27th Apr 08 at 16:52 |
ooooo, im in doncaster for the week so cant really go back there and ive sorta got an egr valve problem now too | |
chris_rosso |
posted on 27th Apr 08 at 16:28 |
Do what was suggested earlier m8, go to an exhaust fitters, get em to heat exhaust up n bend it upwards, worked for me! | |
ali_corsa |
posted on 27th Apr 08 at 12:32 |
i just put an exhaust rubber on the axle and the clamp is basically resting on it, tried pushing the exhaust up and doing the midsection and cat clamp off and twisting it but it didnt work:( just gota put up with it i think | |
ali_corsa |
posted on 26th Apr 08 at 22:51 |
quote: thats the problem they cant fit it right as they have sold me a dodgy part and ran out of midsections to replace it with, so im just after a qucik fix really. i will try undoing the clamp and moving it up and do it back up again if all else fails exhaust rubber will be used. thanks for the help and advice, let you all know how it goes on tomorow:wave: | |
p16vlv |
posted on 26th Apr 08 at 20:49 |
try and pull down on the mounts that are welded to the back box. it should mov the box up | |
marklawton |
posted on 26th Apr 08 at 20:42 |
undo the clamp, then push the exhuast up towards that bottom of the car and then do the clamp up tight again which should take it away for the rear axle, always works for me :) | |
andyc1234 |
posted on 26th Apr 08 at 20:08 |
you just need to fanny about with it bit. if its fitted properly it wont bang | |
joes_1.4_16v_sport |
posted on 26th Apr 08 at 18:23 |
quote: My meathod was an old t-shirt... :0 | |
ali_corsa |
posted on 26th Apr 08 at 18:01 |
i had a new midsection on it today and had a phone call at 12 when i got back saying the part might be damaged but they havent got anymore in stock, took it down there and they arent happy with it, and drop it off monday, but im not at home all next week and its banging on the axle, so i only need a quick fix to last a week | |
james528 |
posted on 26th Apr 08 at 17:51 |
with my old system i just went down kwik fit they heated it an bent it for more clearance only took 5mins an cost £10 new systems fine tho. | |
ali_corsa |
posted on 26th Apr 08 at 17:47 |
is it alright just putting it over the handbrake cable then, im away for a week so its gota last for a week until its back in the garage to be fixed propley as they cocked up | |
mattk |
posted on 26th Apr 08 at 17:43 |
yep, I did the same but with a load of carpet | |
ali_corsa |
posted on 26th Apr 08 at 17:34 |
hey, i need a quick fix for the back box clamp and the rear axle, ive turned the clamp upside down and there is still about 1 cm clearance from the rear axle. what else can i do to stop it banging. would a exhaust rubber cut in half and cable tied over the handbrake cable work? :wave: |