|
Poot
|
posted on 8th Feb 07 at 08:49 |
Ahhh I'll have to keep my eyes open for a c16xe loom on here then:)
What would it run like in safe mode? on the limiter at 3000rpm ect?
btw the help is much appreciated, thanks guys :thumbs:
[Edited on 08-02-2007 by Poot]
|
jazzer2k3
|
posted on 8th Feb 07 at 00:53 |
If u wanna do it correctly, Beardy is correct...
Whichever engine u have *x16xe//c16xe* Ull need the correct Loom for that engine ..
Cos i did an engine swap in my old corsa, first engine was a c16xe always ran in safe mode *Giving the fault code - Knock sensor* ... But it was the loom from a x16xe not a c16 :)
|
Vaux Lad
|
posted on 8th Feb 07 at 00:38 |
The chip, barrel ring and ecu have to match if i remember rightly.
So you couldn't fit a x16xel engine leaving the x16xe transponder/barrel, as that wont work with the x16xel ecu.
You would need a matched 16xel ecu, chip, immobiliser barrel surround.
Im pretty sure thats right anyway.
C16xe doesn't have that system, so you could fit a c16xe with a simple engine loom and ecu change. Wouldn't need do anything else, just leave the immobiliser stuff disconnected.
[Edited on 08-02-2007 by Vaux Lad]
|
Poot
|
posted on 7th Feb 07 at 23:35 |
:boggle:
|
Poot
|
posted on 7th Feb 07 at 18:04 |
so that means...that even with/without the chip and tranponder I already have, the engine still wouldn't start?
|
BeArDy
|
posted on 7th Feb 07 at 18:02 |
As said
- Chip in Ring
- transponder ring around the ignition barrel (which i dont think you need to change as i am sure it only picks up a signal which is sent to the ECU)
- ECU
have to match (not 100% like said weather ring needs doing) otherwise engine will never start, will kick up and cut out after 2 secs flashing ECU light up
|
Warren G
|
posted on 7th Feb 07 at 17:59 |
im 99% surton that the c16xe doesn't have a immobliser/chips
|
Poot
|
posted on 7th Feb 07 at 17:58 |
whats an afm...air flow meter? I've been told that this engine doesn't have an egr valve or something, also the black plastic inlet, not the grey alloy one as seen on x16xe's ect :look:
[Edited on 07-02-2007 by Poot]
|
Gregor
|
posted on 7th Feb 07 at 17:56 |
No it wouldnt due to the c16xe having an afm ?
Correct me if Im wrong
|
Poot
|
posted on 7th Feb 07 at 17:05 |
ttt need to know guys...if anyone knows that is?:boggle:
|
Poot
|
posted on 7th Feb 07 at 12:36 |
So would an x16xel loom and ecu work fine on a c16xe engine ok?
[Edited on 07-02-2007 by Poot]
|
CoastalCorsa
|
posted on 7th Feb 07 at 02:42 |
As far as i am aware there is no chip in the fuel pump
all i know of is the transponder ring around the ignition barrel
The chip in the key
the ecu
them 3 are all interlinked and you need all 3 to be linked
the transponder ring picks up a signal from the chip in your key and transmits this to the ecu - some how
its all to do with the imobiliser
|
Poot
|
posted on 7th Feb 07 at 00:18 |
Hi all,
Got a query regarding the corsa gsi engine ect...
I've been led to believe that the c16xe/x16xe engine's fuel pump had a chip in it, which ws matched to the ECU, chip in the key and the transponder...is this right?
If not, would I have to change the fuel pump, ECU chip and transponde rto match, i.e. one from an x16xel? would I also be right in thinking the x16xel ecu not bring out the full potential of the engine?
many thanks
:)
[Edited on 07-02-2007 by Poot]
|