|
Not logged in [Login - Register] |
You Are Not Registered Or Not Logged In |
Corsa Sport » Message Board » Help Zone, Modification and ICE Advice » gsi tuning » Post Reply
|
L30 SCT |
posted on 18th Aug 06 at 15:59 |
the boy that done the copies were vx_paul from migweb. i would get the mantzel or similar and there is usualy one in the for sale section for about £300 | |
liam8888 |
posted on 18th Aug 06 at 08:38 |
Cheers M8, On the mantzel 1 can ya translate the page to english or can you only read it in german? | |
Dean_W |
posted on 18th Aug 06 at 07:58 |
quote: Mantzels can be bought from Mantzel in Germany. Mine cost around £520 and took a week to come: - http://www.mantzel.com/ Dbilas can be bought from Regal: - http://www.regal-shop.co.uk/ | |
timmee |
posted on 17th Aug 06 at 18:34 |
i can get a new mantzel inlet manifold needs a bit of modding to fit the corsa as it was designed for an astra but it will be suppied to you ready to fit looking for £350 posted | |
liam8888 |
posted on 17th Aug 06 at 18:25 |
Where can ya get a Mantzel inlets from or any other perfomance inlets from its for a 1.6 sport 1999? | |
Dean_W |
posted on 15th Aug 06 at 14:51 |
Either second hand, or bite the bullet and get a new Manifold. | |
Scotty C |
posted on 15th Aug 06 at 14:49 |
quote: Oh. Where else can u get them cheap then? Wait until someone has one forsale on here? | |
Dean_W |
posted on 15th Aug 06 at 14:45 |
quote: The fit is a bit shit though. You need to move the header tank and a couple of other bits. | |
Scotty C |
posted on 15th Aug 06 at 14:39 |
Some-one off Migweb does copy inlets for £200. Well worth it IMO | |
jazzer2k3 |
posted on 15th Aug 06 at 13:58 |
Ye there not that difficult, ull need to be handy with a soldering iron jus a couple of sensors u gotta extend | |
Dean_W |
posted on 15th Aug 06 at 13:47 |
Easy enough. A bit of drilling, extending wires ands head scratching. | |
GTS-T Rob |
posted on 15th Aug 06 at 13:05 |
got the x16xe engine anyway, how hard are they to fit? | |
csweatherston |
posted on 15th Aug 06 at 12:36 |
haha, stage1 tuning = plugs leads and reg :( :( :( | |
Dean_W |
posted on 15th Aug 06 at 12:09 |
quote: Total waste of money. For that money you should look for a second hand Mantzel or Dbilas. Both of these will fit. If your engine is a C16XE, you need the lower inlet from an X16XE. This is the best thing you can do to start off with apart from a good service. [Edited on 15-08-2006 by Dean_W] | |
GTS-T Rob |
posted on 15th Aug 06 at 10:32 |
will that actually make more performance? or just use more fuel? | |
Nick |
posted on 15th Aug 06 at 10:19 |
get the regal auto sport "stage 1" kit | |
GTS-T Rob |
posted on 15th Aug 06 at 10:00 |
whats the most worthwile mods to do tuning/performance wise to start with? my gsi is standard at the moment but looking for a few more horses lol |