|
Not logged in [Login - Register] |
You Are Not Registered Or Not Logged In |
Corsa Sport » Message Board » Help Zone, Modification and ICE Advice » big xe help needed ecu and loom question » Post Reply
|
supacook2k |
posted on 27th Jun 05 at 23:14 |
quote:# i dont have the loom which i why i want to get it all sorted . just spoke to someone who has a loom so should be good to go | |
Nic Barnes |
posted on 27th Jun 05 at 21:32 |
it would concernt me if i had never seen it running, if i had, it would have been fitted by now and i wouldnt be typing this id be out racing imprezza's | |
Richie |
posted on 27th Jun 05 at 21:20 |
why the fuck are you worrying so much over it? You got the engine, loom and the ECU, whats the problem? If you have suspicion that they have given you the wrong bits then make them aware! | |
Nic Barnes |
posted on 27th Jun 05 at 20:00 |
yep but get one with lambda connection | |
supacook2k |
posted on 27th Jun 05 at 19:55 |
quote: its a dizzy engine so i need motronic 2.5 loom right? | |
Nic Barnes |
posted on 27th Jun 05 at 19:24 |
2.8 had different air mass meter, a sensor in the inlet pipe i can only think is inlet temp, a charcoal canister and the loom is different due to no coil, it just has an amplifier. if you can get a 2.5 loom, try get one with lambda. | |
Nic Barnes |
posted on 27th Jun 05 at 19:23 |
yeah, if its got a distributor then 2.5 is the tool for you. if it has an end cap kinda thing over the exhaust cam, then its a dizyless, but judging by the altinator, its a v-belt set up so shouldn be a dizzyless engine | |
supacook2k |
posted on 27th Jun 05 at 19:20 |
how do i know if its a 2.5 or 2.8 ecu? the haynes says my engine is a 2.5. my ecu ends in 019. are there seperate looms for the 2.5 and 2.8 ecu's? | |
Nic Barnes |
posted on 27th Jun 05 at 19:17 |
yeah, probably is. its just after the pipes go into 1, kinda just after where the sump would end going back under the car. | |
supacook2k |
posted on 27th Jun 05 at 19:16 |
is my engine coil pack as the loom i can get hold of is for a coilk pack engine. there is no DIS unit on mine as mine is the early engine? i know i haven't got a clue about theses engines so need all the help i can get? | |
supacook2k |
posted on 27th Jun 05 at 19:15 |
on the manifold that came with the engine there is a big spark plug type thing sticking out of it, so i'm guessing that is the lambda sensor. | |
Nic Barnes |
posted on 27th Jun 05 at 19:11 |
depends on if the ecu is designed to have the lambda probe or not as some early engines didnt have a lambda, although i would have thought if the loom was for a late one with a early ecu on it it would run fine. | |
supacook2k |
posted on 27th Jun 05 at 18:49 |
ok i have an early xe engine. (pic below). the ecu i was given with the engine ends in 019. is that ecu motronic 2.5 or 2.8? would i still need to get a wiring loom for an early xe if the ecu id for a later xe and would it all still work? |