|
|
|
Not logged in [Login - Register] |
 |
You Are Not Registered Or Not Logged In |
|  |
|
Corsa Sport » Message Board » Help Zone, Modification and ICE Advice » Fitting an exhaust manifold » Post Reply
|
| broster |
posted on 5th Feb 04 at 10:30 |
quote: am so! bitch arse | |
| Gavin |
posted on 4th Feb 04 at 19:51 |
:lol: | |
| broster |
posted on 4th Feb 04 at 18:51 |
quote: hahaha, u wanna see another pic of it mate, im including it in my boot install now! lol! to nice to put under my bonnet! P.S. written by a P.I.M.P. daddy! | |
| Gavin |
posted on 4th Feb 04 at 18:45 |
ask broster how to fit one....... on shit u cant cos its stuck up his ass!!!!! | |
| Neshol |
posted on 4th Feb 04 at 17:36 |
:thumbs: | |
| broster |
posted on 4th Feb 04 at 17:26 |
yeah vaux is as good as anywhere else! | |
| Neshol |
posted on 4th Feb 04 at 17:16 |
Ok so I could do with a new set of bolts, and a couple of gaskets. Need them ASAP, where should I go for em? Just go Vaux? Cheers.. | |
| Adam-D |
posted on 3rd Feb 04 at 18:06 |
lol i dont have pas or air con :) | |
| broster |
posted on 3rd Feb 04 at 17:59 |
thank god i dont have air con then! | |
| corsa120 |
posted on 3rd Feb 04 at 17:45 |
also if u have air con u have to remove the gas bottle as i did an costs 40 quid to be refilled | |
| broster |
posted on 3rd Feb 04 at 17:28 |
bugger i have pas, believe im gunna get angry when fitting mine | |
| miles |
posted on 3rd Feb 04 at 17:28 |
I wrapped my janspeed manifold and it cracked... | |
| James R |
posted on 3rd Feb 04 at 16:51 |
Na it's just a sod, and lots of cursing is required to tempt it out. | |
| Neshol |
posted on 3rd Feb 04 at 16:49 |
Cheers for the replies :D | |
| James R |
posted on 3rd Feb 04 at 16:42 |
IF you disconnect it you need a non-PAS steering rack too ;) it's the way forward you know | |
| Greasemonkey |
posted on 3rd Feb 04 at 16:38 |
Coolio | |
| James R |
posted on 3rd Feb 04 at 16:33 |
Ensures a good seal, also make sure you clean off the mating surfaces, bit of towel and cellulose thinners wroks very well. | |
| Greasemonkey |
posted on 3rd Feb 04 at 16:26 |
lol, it is aint it, i might be going back to 15's soon so i could possibly disconnect it, so whats the copper grease for, is it to stop the manifold welding itsself to the gasket etc | |
| James R |
posted on 3rd Feb 04 at 16:24 |
PAS!! That's for women get rid of it if you have it, it's stealing your engines power!! | |
| Greasemonkey |
posted on 3rd Feb 04 at 16:16 |
if ya got PAS good luck getting the lower left manifold bolt off/on its a bitch to get to the PAS pump is in the way lol | |
| broster |
posted on 3rd Feb 04 at 16:12 |
u can buy exhaust wrap for them, or just use the standard shield! ill be fitting mine aswell this week. the bolts on the head may be a pain in the arse to undo, soak them in wd40 for a bit to make it easier | |
| James R |
posted on 3rd Feb 04 at 16:11 |
You'll need a new head to manifold gasket, and the lower gasket that goes on the end of the manifold as they fall apart when you take the old one off. you should in theory get new studs and nuts to go with it, 13mm wrench is what is needed. headshealdig isn't really needed. good luck. oh let the engine be cold, and smear a little copper grease on both faces of new upper gasket and nothing on lower one looks like a ring. | |
| Neshol |
posted on 3rd Feb 04 at 16:08 |
Hey peeps |