|
Not logged in [Login - Register] |
You Are Not Registered Or Not Logged In |
Corsa Sport » Message Board » Help Zone, Modification and ICE Advice » Clock/Info Display Help needed! » Post Reply
|
combat_sri |
posted on 16th Mar 04 at 20:49 |
i have one someone can buy off me for 30quid!lol | |
dirtymagician |
posted on 16th Mar 04 at 20:43 |
There arent any scrappies around here that have them in, it was either £30 or £150 | |
Richie |
posted on 16th Mar 04 at 20:20 |
they are only a fiver from a scrappy | |
dirtymagician |
posted on 16th Mar 04 at 20:17 |
The mfd units are very easy to wreck as anyone on here till testify i ruined mine by trying to change the original bulbs for led ones when i put it back in everything worked but it didnt turn off :lol:. I ended up getting a 2nd hang one for £30 notes, not bad considering a new one from vaux is £150-£200 :! | |
vesko_m |
posted on 16th Mar 04 at 19:35 |
hi ya all. | |
Richie |
posted on 21st May 03 at 18:35 |
the ribbon cable is like a papery type one, it is really easy to break. Ive been thru 2 MFD's :rolleyes: | |
Garnz |
posted on 21st May 03 at 11:31 |
Well to get it out u need to move the centere air vents down u have to push and pull down as iff ya gonna snap em but they do go.When youve done that u have to remove 4 screws to behind each vent look inside @ the top left and right u should see em. Be very careful not to drop the screws get a magnet @ the ready. When thats done u lift the clock surround up and pull out the connector block @ the back. There u can take the bulbs out. I undid to other screws holding the display to the plastic surround out so i was just left wid the display. I used red bulb paint. Now the whole display is red. | |
barry_kellett99 |
posted on 21st May 03 at 07:49 |
Well first of all, The air flow controls part of the dash is proving hard to remove, I have the first air vent pushed down and have access to that, but the second one only pushes back on one side and seems stuck fast on the other site so it is going back inwards lopsided. | |
Cursa |
posted on 20th May 03 at 20:13 |
Do you mean the dials? | |
barry_kellett99 |
posted on 20th May 03 at 15:07 |
Cool... I want to change my LCD display too, As i have to replace my dash bulbs behind the air flow controls... which will just leave the main dash..... HOW DO I GET IT THERE THEN! | |
Richie |
posted on 17th May 03 at 00:56 |
i think you may have damaged the ribbon cable for the mfd. | |
BarinaBoi |
posted on 17th May 03 at 00:43 |
how did you remove the clock? i want to do the same bulb tint, but blue. Do i need to take off the whole dash or can i just somehow unclip the clock? did you actually get the lcd digits to change colour too? my display sometimes gives me letters. but i think its because the lcd digits are faulty. | |
Garnz |
posted on 16th May 03 at 22:21 |
I took the clock/ temp/ date display out to replace and paint the bulbs red so it appers when its on to be red that bits fine! But now when i turn the light on and off it resets everything. But the funny thing is where it normaly has the date it some times has the letter "F" on the left and a number on the right. And some times it tell's me my KMH what going on lol! The wires seem ok and it is plugged in right maybe there is a loose connection somewhere. Has anyone else had this problem? |