|
Not logged in [Login - Register] |
You Are Not Registered Or Not Logged In |
Corsa Sport » Message Board » Help Zone, Modification and ICE Advice » hard breake peddle not stopping » Post Reply
|
monkeytwizzel |
posted on 15th Apr 13 at 21:04 |
Did you said that the brake pedal stayed hard when you started the engine,if so then you do have a servo fault or vacuum leak somewhere!as davegreen said with engine off pump the brake pedal till it goes hard and keeping it pressed start the engine.if it drops when you start the engine then it is ok but if it stays in the same place then you have a servo problem! | |
veccyest |
posted on 14th Apr 13 at 18:33 |
wheels off, nowt looking wrong there must be master / servo | |
veccyest |
posted on 14th Apr 13 at 17:57 |
yer lets what i was then thinking bloodie garages lol. thanks ill take wheels off. | |
davegreen |
posted on 14th Apr 13 at 17:16 |
low pad warning wire come loose maybe? | |
veccyest |
posted on 14th Apr 13 at 17:12 |
yer fluids r fine. | |
davegreen |
posted on 14th Apr 13 at 17:10 |
hand brake warning lights are also used as low fluid level lights on most vauxhalls, have you checked your fluid? | |
veccyest |
posted on 14th Apr 13 at 17:07 |
No not the eml light the hand brake warning light come on when footbrake appiled. ta | |
davegreen |
posted on 14th Apr 13 at 16:41 |
quote: if you have done this and still got hard pedal either the servo or the vacuum pipe to it are at fault. check the pipe first, listen for air leaks, hissing sound along the pipe. is it eml light on? if so it will most likley be an air leak. | |
veccyest |
posted on 14th Apr 13 at 14:12 |
nope brake peddle stay were it is ,. dont drop and is hard ,anymore ideas thanks . | |
veccyest |
posted on 12th Apr 13 at 20:52 |
ok thanks cant wait till tomo | |
Toby |
posted on 12th Apr 13 at 20:51 |
you can check the brake servo on assisted cars by pumping the brake with the engine off and then holding your foot on the brake pedal start the engine and you should feel the pedal drop. | |
monkeytwizzel |
posted on 12th Apr 13 at 20:24 |
When you fix the warning light wiring just make sure that a piston or slider hasn`t stuck in the caliper, | |
veccyest |
posted on 12th Apr 13 at 20:13 |
not as yet bedded in warning light comin.g on as well now | |
Steve |
posted on 12th Apr 13 at 20:09 |
will be vacuum leak on servo somewhere | |
monkeytwizzel |
posted on 12th Apr 13 at 20:08 |
So new discs with those pads and have you bedded the new pads in?did this problem start just after fitting the new pads? | |
jaysc20xe |
posted on 12th Apr 13 at 20:06 |
Mine did this. It was the brake servo pipe that had a slight split in it. | |
veccyest |
posted on 12th Apr 13 at 20:04 |
thanks they are new pads moted last wk & air feed pipe looks ok but will check again many thanks. | |
Martin W |
posted on 12th Apr 13 at 19:48 |
check the air feed for the servo. if its blew off or got a hole in you will have a hard pedal and no brakes. | |
monkeytwizzel |
posted on 12th Apr 13 at 19:43 |
Are your brake calipers ok that`s an indication of seized calipers, sticking or cooked brake pads. | |
veccyest |
posted on 12th Apr 13 at 19:36 |
as above any ideas master clylinder perhaps ? help ta . |