corsasport.co.uk
 

Corsa Sport » Message Board » Help Zone, Modification and ICE Advice » previous owner crashed! help needed! » Post Reply

Post Reply
Who Can Post? All users can post new topics and all users can reply.
Icon:
Formatting Mode:
Normal
Advanced
Help

Insert Bold text Insert Italicized text Insert Underlined text Insert Centered text Insert a Hyperlink Insert Email Hyperlink Insert an Image Insert Code Formatted text Insert Quoted text
Message:
HTML is Off
Smilies are On
BB Code is On
[img] Code is On
Post Options: Disable smileys?
Turn BBCode off?
Receive email notification of new replies?

regfo

posted on 5th Jan 13 at 19:59

bumper wasn't bolted on in that photo, ill see what i can do with the lining up.

also i think the crash bar has been replaced, as there is a bit of a dent in the slam panel also. no damage at all whatsoever to the crash bar.


Aidan-Fleming

posted on 5th Jan 13 at 19:40

so has the crash bar been hit? beacuse that sticks out further than the cross member, unless it was a small stump or summin lol


oba-corsa

posted on 5th Jan 13 at 19:26

bonnet has also moved over O/S no gap to wing and headlight does not fit right to wing.

Drill out spot welds remove cross member replace cross member with new part mig/plug weld new panel in blast of primer stop the rust.
Line bonnet gaps up possible move O/S wing out a little fit some new bumper brackets refit bumper

weekend job. :thumbs:

[Edited on 05-01-2013 by Jason T]


regfo

posted on 5th Jan 13 at 19:18

i removed the crashbar before i took the photo :) still have it in the car :)


Aidan-Fleming

posted on 5th Jan 13 at 18:41

As for the pulling to the left, just get the tracking done.

Does look like someone has had a light bash! Is there not a crash bar behind the bumper? Fixing points are just below the lights either side. Most corsas i see nowadays have had them removed.

But with the bottom cross member, you can cut it out and weld in a new one as ive seen it done before. or you could get a fabricator to make somthing out of bot section.

And yeah that is the outside temperature sensor


regfo

posted on 5th Jan 13 at 17:05

hello,

pretty much first thread on this site, mainly a user on allcorsa :)

have some problems with the car that needs sorted before i get it onto the road.

1:
car pulls to the left when let go of the steering wheel, previous owner said his son curbed the car so bad he popped the tyre of the wheel, i have inspected underneath the car and can't see any thing that looks abnormal, nothing looks bent or so and i measured and compared with other side (drivers side) and seems to be a near match

2:
went down to car today to find that the car has no coolant at all, drained the radiator with some coolant still in the radiator... will need to put the radiator back into the car to pressure test and try and find any leaks, but so far i can't find anything which is worrying of a headgasket failure as i had bad mayo problems and had coolant colored water spraying from the exhaust.

video: 1

also if you notice on the video, near the exhaust you can see the yellowy/brown water.

3:
previously someone has it some sort of post with the car, i noticed this before but didn't look into it fully.

i noticed this by the fact of my front bumper has a largeish dent in the center of the bumper at the bottom:



and later today i inspected further to find this.



looks like the front member is bent inwards quite badly, i really don't know if it's easily repairable, could be bent back into shape? but it looks like someone before me has seen it, and tried to repair any sort of rust down there and had it sanded and sprayed black.

also, the outside temp sensor i think? has been literally glued back on which is quite a bodge job, anybody know if it is the outside temp sensor?



bare in mind my car is a 1999 1.2 breeze with airbags

thanks in advance
:thumbs:

[Edited on 05-01-2013 by regfo]