corsasport.co.uk
 

Corsa Sport » Message Board » Help Zone, Modification and ICE Advice » X16XE Engine Problems - Low revs & Cutting out » Post Reply

Post Reply
Who Can Post? All users can post new topics and all users can reply.
Icon:
Formatting Mode:
Normal
Advanced
Help

Insert Bold text Insert Italicized text Insert Underlined text Insert Centered text Insert a Hyperlink Insert Email Hyperlink Insert an Image Insert Code Formatted text Insert Quoted text
Message:
HTML is Off
Smilies are On
BB Code is On
[img] Code is On
Post Options: Disable smileys?
Turn BBCode off?
Receive email notification of new replies?

nathanx16xe

posted on 3rd Aug 09 at 22:05

may be that then mate but my mine did same thing an it tured out be vaccum pipe


Chris x

posted on 3rd Aug 09 at 09:04

Doubt its that as its ok atm. Its being plugged in properly on Friday so I will see what the outcome is.

The paperclip test keeps flashing up Crank Sensor and by the looks of it on here it apperently does that all the time anyway?


nathanx16xe

posted on 2nd Aug 09 at 21:58

1st i wuld check under your bonnet to see if u can hear air suck or hissing if so find the source and usually it will be a vaccum pipe just put it bk on and u shd be fine let e know mate


X16joeXE

posted on 29th Jul 09 at 18:23

My 1.2 sxi did this and it was only the lamda sensor.


Richardhhha

posted on 29th Jul 09 at 14:29

if its a crank sensor its a pease off pis and will take you all of.. (the time it takes to remove the drivers wheel and undo a nut)


Chris x

posted on 29th Jul 09 at 12:43

Well as said above it came up with fault '0335' which means I need to turn the engine on to get the fault. But when I do that the EML just goes mad. I found the Tigra fault codes as that has the X16XE engine in.

0335 on the tigra code means 'Crank Sensor'

So would the symptoms im having relate to that?

How much is a crank sensor? Where are they located/how do I get to it? Is it an easy job?

Bloody thing! :lol:


Chris x

posted on 29th Jul 09 at 12:40

quote:
Originally posted by Richardhhha
dont need to have the engine running mate.
never have had to on mine and mines got the x14xe engine. same in all things baring cc really

personaly if its reving up and then trying to cut out i'd have a look at vacume hoses..


[Edited on 28-07-2009 by Richardhhha]
It doesnt do it all the time tho so I doubt its that?! :look:


Richardhhha

posted on 28th Jul 09 at 15:54

dont need to have the engine running mate.
never have had to on mine and mines got the x14xe engine. same in all things baring cc really

personaly if its reving up and then trying to cut out i'd have a look at vacume hoses..


[Edited on 28-07-2009 by Richardhhha]


Chris x

posted on 28th Jul 09 at 14:45

I got 10 flashes then a paus then 3 flashes then a pause then 3 flashes then a pause then 5 flashes then a pauss. The EML would then go off for around a second or two then repeat the above.

So looking at the chart it would meen fault 0335, but:

Some ECU systems will also show code 0335 because it doesn't see the engine turning over, this is not a fault because you haven't started the car. Simply start the engine and read the fault codes again. If 0335 shows again while the engine is on, then its a fault. To find out what fuel system you have, read the "Fault Code Chart" below.

So im guessing you need the engine running?! Bloody thing! :lol:


Ellis

posted on 28th Jul 09 at 13:17

This for example - flash, pause, flash, flash = code 12 - 1 flash a pause then 2 flashes.

Code 12 is that start up code IIRC.


Chris x

posted on 28th Jul 09 at 12:29

I have just done it and it was flashing away. I recorded it on my phone. I will upload it when I get back from work.

How do you work it out from the flashes?


Ellis

posted on 28th Jul 09 at 11:10

If the light is on there is a fault code present as far as I am aware.

Sequence starts with a start up code I think, and then flashes the codes and dot-dash way, I've never done it myself so I can't help further than that.

Maybe worth having a bit of paper to write the sequence down.


Chris x

posted on 28th Jul 09 at 10:36

Hello again Ellis :wave: lol

I will give that ago on my lunch break. I will take a video and upload it and see what everyone thinks.

What happens if there is more than one code to read? Or even if there is nothing to read?

Thanks!


Ellis

posted on 28th Jul 09 at 09:56

Try the Paper Clip Test, saves spending silly money on diagnostic computer test.

Someone will help if you don't understand the results.


Chris x

posted on 28th Jul 09 at 09:47

Bit of an update on this:

Basically it started to behave itself again after I put this up. Went to holiday in Newquay and put 1000miles on the car with no problems/issues or anything.

Anyway, the car struggled to start Friday night and the EML was on. I turned it off then back on and it was fine.

Just leaving the works carpark now and it stuggled to start again and the EML was on. Turned it off then on and it was still there.

The revs are sitting around 1000rpm on Idle and it sounds a little bit ruff.

Any ideas? Im guessing I should get it plugged in to see what it brings up? How much does that cost?

Thanks in advance! :wave:


Ellis

posted on 3rd Jul 09 at 09:22

Idle control valve - located on side of throttle body.

Exhaust gas recirculate (sp) valve - underneath lower inlet, it's mare to change :lol:

Can't remember off the top of my head the prices, I know the EGR is in excess of £100 from Vaux, but I wouldn't go buying bits unless you know exactly what the problem is.


Chris x

posted on 3rd Jul 09 at 09:18

What are ICV and EGR? Where would they be located and how much?

Sorry, I really dont have a clue about cars! :lol:


Ellis

posted on 3rd Jul 09 at 09:16

Hmmm I was thinking the usuall suspects - ICV or even EGR, well that was my problem when I had similar symptoms to what you have said.


Chris x

posted on 3rd Jul 09 at 09:14

Nope, nothing.


Ellis

posted on 3rd Jul 09 at 09:13

Is your EML on?


Chris x

posted on 3rd Jul 09 at 09:11

Hi Guys,

My Sport has started playing around.

Basically, when driving and coming to a stop I put my foot on the clutch and the revs drop so it nearly stalls. It then revs itself so the engine doesnt stall and then goes back to normal after a second. It did it driving yesterday but the engine stalled whilst driving after puting my cluctch down.

It doest it a couple of times aday but only stalled for the first time yesterday.

Dont no if its a sensor playing around?

All ideas/help would be great. It as its MOT at 2.15pm anyway :rolleyes:

Thanks! :wave::)