corsasport.co.uk
 

Corsa Sport » Message Board » Help Zone, Modification and ICE Advice » Coolant renewal on 1.2 8v » Post Reply

Post Reply
Who Can Post? All users can post new topics and all users can reply.
Icon:
Formatting Mode:
Normal
Advanced
Help

Insert Bold text Insert Italicized text Insert Underlined text Insert Centered text Insert a Hyperlink Insert Email Hyperlink Insert an Image Insert Code Formatted text Insert Quoted text
Message:
HTML is Off
Smilies are On
BB Code is On
[img] Code is On
Post Options: Disable smileys?
Turn BBCode off?
Receive email notification of new replies?

mg1969

posted on 30th Jan 08 at 13:36

Bugger! Tried to do this today, and when trying to loosen the fan switch, the threads on either the rad or the switch must have gone as it is spinning in thin air (what would your money be on?). As as a result I cannot get the damn thing off, not helped by the fact that I am using an adjustable wrench and the limited space under there.

I have temporarily tightened it back up, but there is now a slow leak from there. A 28mm deep socket will make life a lot easier so when I get hold of one I will give it another go.

Just hoping I can salvage the situation now without having to buy additional new parts. :(


waters

posted on 29th Jan 08 at 17:16

yes mate I flushed all the lot, engine, radiator and removed header tank, put some bleach in it, put cap on and gave a really good shake (block the pipes) and it came up like new.....got all gunk out of system!


mg1969

posted on 29th Jan 08 at 13:32

quote:
Originally posted by waters
I've just done mine......I used 40 %...and yes it is expensive stuff!


:thumbs: Did you flush the engine too waters?

And its supposed to last a lifetime from factory! Well at least it should not need changing again ;)


mg1969

posted on 29th Jan 08 at 13:28

ok cheers Kurt


waters

posted on 29th Jan 08 at 13:28

I've just done mine......I used 40 %...and yes it is expensive stuff!


Kurt

posted on 29th Jan 08 at 13:25

well i was always told not to over do it.. haynes know more than me though.. so i imagine 50/50 should be fine

[Edited on 29-01-2008 by Kurt]

just quickly read up on it and yeah 50/50 is usally fine.. but using too much can do all sorts of damage including water pump failure and clogged radiator passages..

[Edited on 29-01-2008 by Kurt]


mg1969

posted on 29th Jan 08 at 13:23

quote:
Originally posted by Kurt
dont use too much coolant though, that can also cause corrosion


Really, I didnt know that. What would you recommend? Haynes suggests anything between 20% and 52% depending on how low a temp you want to protect against. I was going to aim for the upper limit, but maybe that's a little high?


Kurt

posted on 29th Jan 08 at 13:12

dont use too much coolant though, that can also cause corrosion


mg1969

posted on 29th Jan 08 at 13:03

Thanks for the additional tips guys.

Yes, the temp sender unit is lower down so makes sense to drain from there.

Did none of you guys remove the thermostat to flush the engine too? Doesn't sound like its necessary.

I'll try to measure how much coolant comes out, as I want a high percentage of coolant to water when topping back up (hopefully to prevent any further corrosion). This will after all be diluted with what is left in the engine.

By the way, not cheap stuff is it. Vauxhall charged me £26 for 5l.


Richardhhha

posted on 29th Jan 08 at 11:14

and when you fill the thing back up do so slowly, dont let the coolant/water just slosh into the coolant bottle pore it in slowly as this will help reduce any air in the system, also when thats done turn the heater fans to hot and full speed, run the car and your a gooden


Kurt

posted on 29th Jan 08 at 10:54

when i did mine i drained it from the temp sender on the bottom of the rad on the left side.. id let it cool down though.. i was impatient and had my hands round a hot brass sender and my arm next to a hot hose...


mg1969

posted on 29th Jan 08 at 09:09

Thanks for the reply carnuts.

The thermostat is working fine. I will do as you say, drain from radiator and flush :thumbs:


carnuts

posted on 29th Jan 08 at 00:30

all depends if the thermostat is ok or not if its ok and you just want to change the coolant over then its simple enough just take the hose off the bottom of the radiator and hold it down and let it come out into a bucket or similar

flush as you want with just water and then put the hose back on and fill it back up with some anti freeze and some water run her up with the cap off for little while let the air come out and put the heater on and check that its nice and warm

if so job done


mg1969

posted on 29th Jan 08 at 00:07

I want to renew the coolant on my 1.2 8v as there are signs of corrosion in the expansion bottle, plus mixture looks to watery.

I read through Haynes' how to and the bit about flushing the engine sounds a bit scary. Youve got to remove the drive belt to get to the thermostat. Ive never done this before and would be concerned about getting it on it right again.

Question is if I dont flush the engine (and just do the rad) will the job not be a goodun?

Cheers.