|
Not logged in [Login - Register] |
You Are Not Registered Or Not Logged In |
Corsa Sport » Message Board » Help Zone, Modification and ICE Advice » bought an engine » Post Reply
|
paolo |
posted on 1st Aug 07 at 18:37 |
thank you for all the information guys, its been really realy helpful! sooo I think I am all ready to get the engine fitted! | |
Dave A |
posted on 31st Jul 07 at 21:03 |
yes will fit perfectly but will be slightly more restrictive than a 1.6 one. | |
paolo |
posted on 31st Jul 07 at 20:45 |
soo if I use the x14 inlet will it mate up ok?? but will it cause a restriction being smaller | |
Dave A |
posted on 31st Jul 07 at 20:42 |
injectors are the same, x16xe has bigger ports than the x14 but x14 can be used. | |
paolo |
posted on 31st Jul 07 at 20:35 |
thanks for clearing that up cam, so I will also need a lower inlet? or can I get away with the x14xe inlet? also or the injectors the same then? | |
Dave A |
posted on 30th Jul 07 at 20:01 |
can use the x14xe injectors. | |
TheCam |
posted on 30th Jul 07 at 19:55 |
| |
paolo |
posted on 30th Jul 07 at 19:46 |
anyone?? | |
paolo |
posted on 29th Jul 07 at 18:16 |
no no not rude atall..am I buggery fitting it my self...just wanted to know that I had everything?? | |
sam13 |
posted on 29th Jul 07 at 17:19 |
if you dont know were the head is and your going to be putting that engine in im worried for you. | |
paolo |
posted on 29th Jul 07 at 16:41 |
will the injectors from the x14xe be ok? with it being a bare engine am worried something wont fit?? | |
Scotty C |
posted on 28th Jul 07 at 18:38 |
The head is there! | |
paolo |
posted on 28th Jul 07 at 18:35 |
not too up on engines lol, thanks for the help guys...soo were all ready to put it in? | |
Vaux Lad |
posted on 28th Jul 07 at 18:33 |
The heads there/\ lol | |
paolo |
posted on 28th Jul 07 at 18:28 |
| |
Scotty C |
posted on 28th Jul 07 at 18:09 |
If you're buying just a block, no the head will not be there! x14 inlet will fit | |
paolo |
posted on 28th Jul 07 at 17:35 |
thank you for the helpful coments..to fro-dizzle I got these items. and to monster will the head not be there?? I hope soo. also will the inlet from the x14xe fit?? | |
Scotty C |
posted on 28th Jul 07 at 17:27 |
no point using your x14xe head! | |
Vaux Lad |
posted on 28th Jul 07 at 17:15 |
It will be "stiff" in places, thats the compression building up as the piston reaches tdc..... | |
Fro |
posted on 28th Jul 07 at 17:14 |
Transponder, and chip from the key. | |
paolo |
posted on 28th Jul 07 at 16:41 |
hi there:thumbs: bought a x16xe today:), its just the block. I aslo got ecu and loom...will there be anything else that i need to put it in my x14xe corsa?? also when turning the crank by hand on the x16xe it feels stiff in places, is this normal?? |