corsasport.co.uk
 

Corsa Sport » Message Board » Help Zone, Modification and ICE Advice » fitting revcounter / tacho » Post Reply

Post Reply
Who Can Post? All users can post new topics and all users can reply.
Icon:
Formatting Mode:
Normal
Advanced
Help

Insert Bold text Insert Italicized text Insert Underlined text Insert Centered text Insert a Hyperlink Insert Email Hyperlink Insert an Image Insert Code Formatted text Insert Quoted text
Message:
HTML is Off
Smilies are On
BB Code is On
[img] Code is On
Post Options: Disable smileys?
Turn BBCode off?
Receive email notification of new replies?

ricky1989

posted on 29th May 06 at 15:40

my corsa doesnt have a green wire, and what side is the negative side to teh coil?


MR2Mike

posted on 25th Aug 05 at 21:13

no problem tom :thumbs::D glad it worked !


Siberia

posted on 24th Aug 05 at 13:50

sure taking the clocks out is a 10 minute job...


tom_simes

posted on 24th Aug 05 at 10:48

I didnt wana take the chance cos from reading other posts on here, base model old corsas like mine (93 LS) don't always have them, and I cudnt be bothered to take the clocks out to find it wasnt there!


ed

posted on 24th Aug 05 at 10:40

quote:
Originally posted by tom_simes
ed look in the post above mate-
Just said I run it to the coil and all works perfectly! LOL
Can't wire it up to clocks, as no tacho there
On most Corsa's there is still a green wire to use even if you have no rev counter on your clocks.


tom_simes

posted on 24th Aug 05 at 09:52

I already have an amp power lead through the bulkhead, right next to the battery, and the coil is also next to the battery. All I had to do was thread the cable through the same grommet as the power cable and under the battery and then splice it in to the coil wiring, only bout a 15 minute job under the bonnet!


Will94

posted on 23rd Aug 05 at 23:26

There is a green wire down behind the kick panel... would have been a bit easier than running one all the way under the bonnet but least you got it working!
If you did decide to neaten it up tho then take off the kick panel (unscrew it then slide it down a bit, otherwise the bonnet handle will jus flex outta the way) and there will be a square plug right at the front. 9 wires going in from the ECU (one of these is the green one you need) and on the other side of the plug there is 8... which go up behind the dash. In the 1.2 8v SPi models this is where the loom differs from the 1.4 8v SPi... the green wire isnt carried on! This is the intended signal wire which runs a rev counter....and then you wont have cables trailing around your engine bay.

Either way least it works :P


tom_simes

posted on 23rd Aug 05 at 15:12

ed look in the post above mate-
Just said I run it to the coil and all works perfectly! LOL
Can't wire it up to clocks, as no tacho there


ed

posted on 23rd Aug 05 at 14:52

Green wire should be on the loom behind the clocks on the big multiplug.

Otherwise run a wire to the - terminal on the coil.


tom_simes

posted on 23rd Aug 05 at 13:53

mike, just wana say thanks mate, wired it up to the negative side and all works great!
Thanks mate


MR2Mike

posted on 17th Aug 05 at 14:36

yeh pal, worked for me :thumbs:

good luck


tom_simes

posted on 17th Aug 05 at 14:33

ok thanks mike so just run green wire to negative side of coil and it should work no probs? obviously connect up earth and switched live as well!

[Edited on 17-08-2005 by tom_simes]


MR2Mike

posted on 17th Aug 05 at 14:23

ok mate, its on the right hand side of the engine as you look at it. a box with one lead from the distributor going to it i think :o havent got any pics of the old engine sorry, was too ashamed of it to take any lol. its not that hard to find mate, if you send a pic of the engine to me, ill put a ring around it for you.

good luck :thumbs:


tom_simes

posted on 17th Aug 05 at 14:13

its 1.2 93 plate


MR2Mike

posted on 17th Aug 05 at 14:13

what engine is it? i did it on my old 1.2 but now have a 1.4 and its totally different system, not a clue on the 1.4


tom_simes

posted on 17th Aug 05 at 13:59

got any pics?


MR2Mike

posted on 17th Aug 05 at 13:25

the green wire of the rev counter goes to the coil pack i think (negative side)

[Edited on 17-08-2005 by Mike_Corsa]


tom_simes

posted on 17th Aug 05 at 09:34

I have looked at othe posts on here, and most say to coonect the green wire from the tacho to a green wire on the ECU behind the drivers kick panel.
I was just wondering, has anyone got a photo of this section of the ECU, so I can see what I'm doing? And what is the quickest way of getting the kick panel off, cos I think the bonnet release handle is in the way?
Any help will be much appreciated.
Thanks guys and gals