|
Not logged in [Login - Register] |
You Are Not Registered Or Not Logged In |
Corsa Sport » Message Board » Help Zone, Modification and ICE Advice » Is it safe to... » Post Reply
|
ed |
posted on 20th Feb 04 at 12:54 |
Yea, thats what my mate told me to, he learnt how to do it at motor sport college on this scooby they were building. I'm gonna double check with him how to do it, or even better get him to do it for me... | |
dantheman |
posted on 20th Feb 04 at 11:42 |
yere i think im gona do as you said drill holes in the rear foort well behind thwe front seats and mount my harnesses there but im gona reinforce them underneath. | |
ed |
posted on 20th Feb 04 at 11:30 |
Put buckets in! It's pretty easy. Well in theory it is... My old man reckons I could do it myself... | |
dantheman |
posted on 20th Feb 04 at 00:23 |
i also wana do this with the front harnesses ive seen it done in a corsa in a magazine once and i wana either put buckets in the back or keep the rear bench. i really done wana use the excistin mounts on the rear. | |
ed |
posted on 19th Feb 04 at 23:57 |
Na the back bench has gone... I'm putting a pair of bucket seats in the back... I think I got everything covered, I need to make a few holes, weld a few plates in, or make some huge washers for the back harnesses, and use some of the existing points to attatch the front harnesses... It's gonna take a bit of planning but should work out. | |
Greg_M |
posted on 19th Feb 04 at 23:30 |
where can you attach harnesses if you wanna keep the back bench? | |
ed |
posted on 19th Feb 04 at 23:22 |
Yea, I gotta remove the fuel tank for bolting the subframes, I'm fabricating to hold the rear seats in, down. | |
Ian |
posted on 19th Feb 04 at 22:24 |
If you're securing things to the floor then you're safe to drill through - just use a huge washer or plate underneath as upside suggests. | |
ed |
posted on 19th Feb 04 at 22:01 |
Does anyone else know anything about this? Would it be ok to bolt the back harness to the original mounts, cos looking at it, its gonna be pretty tight... | |
ed |
posted on 19th Feb 04 at 16:29 |
ahhh good idea! Where would I bolt the front harnesses to? Would it be safe to bolt them to where the original rear seat belt loops over, at the highest point? | |
stuyw |
posted on 19th Feb 04 at 16:26 |
u dont drill any holes as u use the original ones which are located under where the rear seats used to be | |
LukeGSi |
posted on 19th Feb 04 at 16:26 |
all buckets look shit with standard seatbeats IMO so definatly go for harnesses but secure them properly :thumbs: i was tempted to go for back buckets to but decided to get rid of rear seats all together!! :D | |
ed |
posted on 19th Feb 04 at 16:24 |
Yea, you don't bodge seatbelts! I wanted to use the standard seatbelts, cos of the safety issue, but there just isnt going to be room with the bucket seats in there... And I really wanna have back buckets! | |
LukeGSi |
posted on 19th Feb 04 at 16:21 |
if you do i would recommend either putting a huge washer type thing underneath or yeah weld to give extra strength - seat beats/harnesses aint things to be bodged!! | |
ed |
posted on 19th Feb 04 at 16:19 |
Drill holes in the floor pan to bolt harnesses? My mate said he did it in a Scooby in college... But he didnt say if he needed to weld a plate underneath to give it a bit more strength? Anyone know? |