|
Not logged in [Login - Register] |
You Are Not Registered Or Not Logged In |
Corsa Sport » Message Board » Help Zone, Modification and ICE Advice » LED dash conversion » Post Reply
|
danregs |
posted on 28th Jan 04 at 18:49 |
yeh i was looking for some blue ones please! :thumbs: | |
cobra148 |
posted on 28th Jan 04 at 18:33 |
I can only do the heater panel in red, blue, white or green at the moment in plug and play. | |
danregs |
posted on 28th Jan 04 at 18:15 |
quote: any chance you could sell one or two to me? :P | |
cobra148 |
posted on 28th Jan 04 at 18:05 |
I've been known to sell one or two ;) | |
danregs |
posted on 27th Jan 04 at 22:01 |
ok thanks for ur help mate. i dunno whats up with mine then :boggle: u know where i can get some plug and play ones from by any chance, just for the heater controls (cos my dash setup works ok). | |
cobra148 |
posted on 27th Jan 04 at 20:56 |
Should be no problem then, a 470 resistor will let you run a typical 3.3v 20ma led at 12 volts or more no problem, thats what I've been using for nearly 2 years now. | |
danregs |
posted on 27th Jan 04 at 20:49 |
yeh sorry mate - typo! i meant 470! and i'm pretty sure they are about 8000mcd. they are fookin brite!:! | |
cobra148 |
posted on 27th Jan 04 at 20:24 |
Do you mean 470 Ohm, you can't get a stock resistor at 460. How are you actually fitting them, also, do you know the mcd (brightness) rating, you say they are "superbrite", I've seen 3000-4000mcd leds described as this, but they will be too dull for your dials. | |
danregs |
posted on 27th Jan 04 at 20:15 |
no idea on the spec mate. got the LEDs from ebay and the guy said in the auction that they would work on 12V with the resistors he provided (which are 460-ohm). i guess i shouldnt have taken his word for it! gonna have to find my own resistors. what would you recommend for 12V application if i'm replacing a 1.2W bulb? i also noticed that now i've replaced my interior lights with LEDs (that did have 5W bulbs in them) the LED's stay on dimly when the interior light should be off :boggle: | |
cobra148 |
posted on 27th Jan 04 at 19:52 |
Dave, if your dash and heater lights are all going on and off together, that sounds like an electrical problem. | |
Dave_Gordon |
posted on 27th Jan 04 at 17:37 |
ok m8 let us nkow and gud luck!!!! | |
danregs |
posted on 27th Jan 04 at 17:21 |
ive just spent all avo trying to get mine to work. they just keep blowing fuses tho! i didnt buy plug and play ones, i bought superbrite blue LED's and rigged them in with some resistors that shulda worked ok.......but they dont :boggle: | |
Dave_Gordon |
posted on 27th Jan 04 at 15:41 |
well gutted cause they looked cool!!! | |
broster |
posted on 27th Jan 04 at 15:39 |
nope, i tried that also, as i ran outs fuses so ran bigger ones, they went pop too! iv now got no center consol lights! these the ones with little circuit boreds on then | |
Dave_Gordon |
posted on 27th Jan 04 at 15:36 |
can anything bedone or do i get theold ones out of the bin and hope they aint broke!!! | |
broster |
posted on 27th Jan 04 at 15:23 |
mine were the same, for the heater switch panel/center consol, they just keep blowing fuses! | |
Dave_Gordon |
posted on 27th Jan 04 at 15:16 |
So it aint just me!!!! dunno just asked for led's off cobra and he sent out plug and play ones, they plug but don't play. | |
danregs |
posted on 27th Jan 04 at 14:36 |
uh oh! what LED's and resistors did you use mate? i've just tried mine and i've blown 3 fuses :! i cant seem to get them in and workin! i'm an electronic engineer too, which is a bit embarrassing! :lol: | |
Dave_Gordon |
posted on 27th Jan 04 at 11:48 |
I also done me dash looks cool but they keep goin off with me heater control led's. i had to drive 30 miles without dash lights???? | |
danregs |
posted on 27th Jan 04 at 11:40 |
cheers mate!! :thumbs::thumbs::thumbs::) | |
Dave_Gordon |
posted on 27th Jan 04 at 11:36 |
I hav just replaced my dash and heater bulb controls m8!!! | |
danregs |
posted on 27th Jan 04 at 11:22 |
i'm gonna do an LED conversion on the dash of my Corsa C, but any1 got any idea how i get my heater control panel off to get in behind it to the bulbs, so that i can replace them? :boggle: |