corsasport.co.uk
 

Corsa Sport » Message Board » Help Zone, Modification and ICE Advice » Rockford Bd500.1 momoblock amp at 1ohm?! » Post Reply

Post Reply
Who Can Post? All users can post new topics and all users can reply.
Icon:
Formatting Mode:
Normal
Advanced
Help

Insert Bold text Insert Italicized text Insert Underlined text Insert Centered text Insert a Hyperlink Insert Email Hyperlink Insert an Image Insert Code Formatted text Insert Quoted text
Message:
HTML is Off
Smilies are On
BB Code is On
[img] Code is On
Post Options: Disable smileys?
Turn BBCode off?
Receive email notification of new replies?

DC

posted on 26th Jan 04 at 17:41

No1 else got an opinion. Snowy, Austin neither of u 2 no if 1 ohms gonna b ok!!

Surely theres other ppl on here that hav or still r running at 1ohm.

Pretty much sure am gonna give it ago just wanted some more opinions.

Cheers, D


Carb_Fanatic

posted on 25th Jan 04 at 19:27

you can cos all that the amp see's is a load........

dont matter if ones more than the other really.......

just finished a ****ing university assignment of resistance and loads, i hate all work........


DC

posted on 25th Jan 04 at 13:33

thanx for that gives me a bit more confidance. Corb u got any opinion on what Carb Fanatic said? Do u no if you can mix n match voicecoils? I always thought u cudnt not sure why tho!!


corb

posted on 25th Jan 04 at 12:58

Ive got a Ground Zero amp which is only 2ohm stable but ive run it for a year at 1ohm and had no problems!


DC

posted on 25th Jan 04 at 12:40

i no how to work out what my amp wil be runnig at when connecting up different amounts of subs but how do u work it out when its differing voicecoils and when 1 is run say run in parellel and the other series etc. Basically how didi u get the figure of 1.6 ohms?


DC

posted on 25th Jan 04 at 11:53

I didnt no u cud mix n match voicecoils like that. Was always led 2 believe that you could only run subs of the same voicecoils.


Carb_Fanatic

posted on 25th Jan 04 at 11:49

hey, i had the RF top of the range one.

they get VERY hot running at 1ohm and there is a high chance of the heat override thingy cutting in and reseting your amp. it would work fine until you crank it up...........

if you wanna try it then be prepaired that your amps life will be in danger.....and it`ll last no-where near as long.

another way is to run your current sub at the 2ohm then add a dual 2ohm sub wired as 4 ohm. then wire the two subs in parallel to give the amp a load of 1.6ohm. should be a little safer.......


DC

Icon depicting mood of post posted on 25th Jan 04 at 11:32

Ok, ive got a RF Bd 500.1 Mono block powering a JL W3 12" Dual 4ohm voicecoil version. Its wired in parallel so the amp is seeing 2ohms.

Thing is i want another W3 to run off the same amp but this causes me some impedence problems. Once a wire the 2nd sub up it means if i have them wired parellel (like now) the amp will be seeing 1ohm!! However if i wire them in series the amp will be only seeing 4 ohms and the amp wont be producing the power i want.

If i had thought long term when i bought the first W3 i would have got the Dual 2 ohm voicecoil version because then i could run two subs in series at 2ohms.

I told my local Ice Dealer (Audio Island) where all my money goes the dilema and they said although it will void the RF warranty running at 1 ohm as long as i use like 2 guage power cable etc i shouldnt have a problem. The main installer there is running 2 dual voicecoil RF 10" subs off the same Bd500.1 i have and he says he has had no problems running at 1 ohm.

Was just wondering if any of you guys were running a similar ish spec RF amp at 1 ohms and if ya had any problems. Any insight and opinions would be appreciated.
Cheers, D :thumbs: