|
Not logged in [Login - Register] |
You Are Not Registered Or Not Logged In |
Corsa Sport » Message Board » Help Zone, Modification and ICE Advice » How have you all put.... » Post Reply
|
RichR |
posted on 27th Dec 03 at 18:41 |
| |
the_legend_of_yrag |
posted on 27th Dec 03 at 17:12 |
quote: Tis where i ended up going :lol: | |
baza31 |
posted on 27th Dec 03 at 15:03 |
pop off ur cluster cover in ur boot, theres plenty of places in there. | |
Dom |
posted on 26th Dec 03 at 13:50 |
one of the ground places is the rear seat belt bolts....but dont hold me to that mate with it being the best place, but as long as its a clean bit of metal (no paint on it) then it should be fine :) Where ever you choose mate, give it a scrub with wire wool and brush it off. Just to make sure there will be good contact :) | |
the_legend_of_yrag |
posted on 26th Dec 03 at 13:17 |
my wire is 4 gauge so wernt too bad, one thing, wheres the best place to ground it in the boot??? | |
Dom |
posted on 26th Dec 03 at 12:53 |
is 2 gauge to big to run down the sills ??? | |
robtj |
posted on 26th Dec 03 at 03:05 |
i removed the carpet, cause i was having problems running a 2 gauge power cable down the side, but for smaller setups just run it under the lower door plastic. as for the tools i bought a cheap set of star keys for £2 from a local shop. does the same job | |
baza31 |
posted on 25th Dec 03 at 21:17 |
the torx ket is a T25, jus thoght i´d let u know. its a piece of pis to run cables to ur boot. | |
AdiSRI |
posted on 24th Dec 03 at 18:57 |
I'm pulling my whole car to bits and am gonna dynamat floor under carpet etc.. as me damn zorst is soo noisy it ruins the music! | |
IntaCepta |
posted on 23rd Dec 03 at 14:25 |
i managed to do it without taking the seats out (didn't have a big enuf torx bit for the seats). but took the sills out and lifted teh carpet up as much as poss. | |
beav |
posted on 23rd Dec 03 at 14:04 |
Definitly no need to take out seats, it can be easily done without this by just runnig it along the sills under the plastic! | |
Voyto |
posted on 23rd Dec 03 at 13:04 |
i took out my passenger seat and rear bench seat. also took up all the carpet. well worth it IMO. just takes a long time and make sure u remember where ever bolt goes. ive got about 2 little screws that i cant remember where they went :boggle: | |
beav |
posted on 23rd Dec 03 at 12:38 |
Yip, you'll need one of those little 'torx screws'. Everyone knows someone with one of those, get phoning round yuor mates if you don't have one or the right size. It can take a little time to put all the wires through the car but definfitly worth it in the end! | |
the_legend_of_yrag |
posted on 23rd Dec 03 at 12:33 |
need a torx screw tho dont i to get the sills up? | |
corb |
posted on 23rd Dec 03 at 06:53 |
run it under the side sill thingys, but mines (power cable)straight up the centre of the car. | |
the_legend_of_yrag |
posted on 23rd Dec 03 at 05:33 |
... your wiring in?? Did you take seats out and pull carpet up like in the haynes manual, id rather not do this!! |